Gigabyte G293-S40 Скачать руководство пользователя страница 43

Страница: 43 / 118

- 43 -

System Hardware Installation

3-7 Installing the Hard Disk Drive

Read the following guidelines before you begin to install the Hard disk drive:
• Take note of the drive tray orientation before sliding it out.

• The tray will not fit back into the bay if inserted incorrectly.

• Make sure that the HDD is connected to the HDD connector on the backplane.

Follow these instructions to install a 2.5" hard disk drive:

1. Press the release button.

2. Extend the locking lever.

3. Pull the locking lever in the direction indicated to remove the HDD tray.

4. Align the hard disk drive with the positioning stud on the HDD tray.

5. Slide the hard disk drive into the HDD tray.

6. Reinsert the HDD tray into the slot and close the locking lever.

CAUTION!

We strongly recommend using enterprise level hard disk drives in the Gigabyte server system. For
more information of recommended HDDs, please visit the Gigabyte website:

https://www.gigabyte.com

and search for the specific product QVL from

Support & Downloads.

Содержание G293-S40























































































































Результаты поиска

Содержание G293-S40

Отзывы:

Похожие инструкции для G293-S40

Бренды по названию

Популярные бренды

Gigabyte G293-S40, Руководство пользователя

Результаты поиска

Содержание G293-S40

Отзывы:

Похожие инструкции для G293-S40

Бренды по названию

Популярные бренды