Gigabyte G293-S40 Скачать руководство пользователя страница 35

Страница: 35 / 118

- 35 -

System Hardware Installation

Model B

For Slot1/Slot2/Slot3/Slot4/Slot13/Slot14/Slot15/Slot16

Follow these instructions to install the GPU card:

1. [For Slot13/Slot14/Slot15/Slot16] Loosen and remove the two screws securing the PCI cage at the

top of the system.

[For Slot1/Slot2/Slot3/Slot4] Loosen and remove the single screw at the top of the system and the

two screws at the rear of the system securing the PCI cage.

2. Pull the two plastic handles to lift up the PCI cage from the system.

3. Insert the card into the selected slot. Make sure that the card is properly seated.
4. Secure the GPU cards in place with two screws.

Front

Rear

Boom: Slot4 (PCIE_1_PCIE_1)

Top: Slot1 (PCIE_1_PCIE_4)

Boom: Slot16 (PCIE_4_PCIE_1)

Top: Slot13 (PCIE_4_PCIE_4)

Slot14 (PCIE_4_PCIE_3)

Slot15 (PCIE_4_PCIE_2)

Slot2 (PCIE_1_PCIE_3)

Slot3 (PCIE_1_PCIE_2)

(For Slot13/Slot14/Slot15/Slot16)

Содержание G293-S40























































































































Результаты поиска

Содержание G293-S40

Отзывы:

Похожие инструкции для G293-S40

Бренды по названию

Популярные бренды

Gigabyte G293-S40, Руководство пользователя

Результаты поиска

Содержание G293-S40

Отзывы:

Похожие инструкции для G293-S40

Бренды по названию

Популярные бренды