26
UK
F4
Movements made during the learning with 2 motors:
Ÿ
Motor 2 closes until running into the limit switch or until receiving a START impulse.
Ÿ
Motor 1 closes until running into the limit switch or until receiving a START impulse.
Ÿ
Pause of 1 second.
Ÿ
Motor 1 opens until running into the limit switch or until receiving a START impulse.
Ÿ
Motor 2 opens until running into the limit switch or until receiving a START impulse.
Ÿ
Pause of 1 second.
Ÿ
Motor 2 closes until running into the limit switch or until receiving a START impulse.
Ÿ
Motor 1 closes until running into the limit switch or until receiving a START impulse.
Ÿ
Pause of 1 second.
Ÿ
Motor 1 opens, the first START command causes the beginning of the decelerated motion, the following
START command or the opening limit switch causes the end of motor 1 motion in opening.
Ÿ
Motor 2 opens, the first START command causes the beginning of the decelerated motion, the following
START command or the opening limit switch causes the end of motor 2 motion in opening.
Ÿ
Pause of 1 second.
Ÿ
Motor 2 closes, the first START command causes the beginning of the decelerated motion, the following
START command or the closing limit switch causes the end of motor 2 motion in closing.
Ÿ
Pause of 1 second.
Ÿ
Motor 2 closes, the first START command causes the beginning of the decelerated motion, the following
START command or the closing limit switch causes the end of motor 2 motion in closing.
Ÿ
End of learning, the LED L9 and the flashing light signal that the learning has been completed and turn off.
Movements made during the learning with 1 motor:
Ÿ
Motor 1 closes until running into the limit switch or until receiving a START impulse.
Ÿ
Pause of 1 second.
Ÿ
Motor 1 opens until running into the limit switch or until receiving a START impulse.
Ÿ
Motor 1 closes until running into the limit switch or until receiving a START impulse.
Ÿ
Motor 1 opens, the first START command causes the beginning of the decelerated motion, the following
START command or the opening limit switch causes the end of the motion of motor 1 in opening.
Ÿ
Pause of 1 second.
Ÿ
Motor 1 closes, the first START command causes the beginning of the decelerated motion, the following
START command or the closing limit switch causes the end of the motion of motor 1 in closing.
Ÿ
End of learning, the LED L9 and the flashing light signal that the learning has been completed and turn off.
In the event of the learning procedure not work then check the signaling of LED L9.
• Make some opening and closing cycles to check the right operation of the automation and adjust the doors
force, acting on FORCE trimmer. If you have to make large adjustments from the values used during the learning
sequence then it may be necessary to repeat the learning procedure.
• Check the right operation of the automation.
14 - FINAL CHECKS
27
UK
F4
Effect
Gate/door locked
Device
Edge detection before motion
Signalling
3 slow flashes
CE Declaration of conformity
The manufacturer:
GI.BI.DI. S.r.l.
Via Abetone Brennero, 177/B,
46025 Poggio Rusco (MN) ITALY
declares that the product:
F4 ELECTRONIC CONTROL UNIT
is in conformity with the following EEC Directives:
and that the following harmonised standards have been applied:
• LVD Directive 2006/95/CE and subsequent amendments
• EMC Directive 2004/108/CE and subsequent amendments
•
EN60335-1
• EN 61000-6-2, EN 61000-6-3
The Legal Representative
Michele Prandi
Date 05/07/2019
15 - SUMMARY OF FLASHING LIGHT SIGNALLING
Photocell break/interruption at rest in presence of
a START command ( DIP1_1 = ON )
5 fast flashes
When released, it opens
Opening
Closing
0,8s ON, 0,8s OFF
0,4s ON, 0,4s OFF
The gate is opening
The gate is closing
LEARNING OK
Learning correctly made
LEARNING FAILED
Learning failed
3s ON, 1s OFF
Repeated 3 times
0,3s ON, 0,3s OFF
Repeated 4 times
Содержание AS06320
Страница 58: ...NOTE NOTES 58 F4 ...
Страница 59: ...NOTE NOTES 59 F4 ...
