(2) Power Specifications
8. Photovoltaic Function Connection
This appliance provides the function to use the energy from photovoltaic system. Users
can
choose
to
use
this
function
if
a
photovoltaic system
is installed
.
The photovoltaic function is enable when a contact signal is established between the two wires of
t
he photovoltaic inverter connecting cable. T
his
function can exploit any overproduction of
electricity and it increases the water temperature until it reaches the heat pump default
temperature 65
℃.
Power
Power Cord Diameter
(mm )
2
Manual Switch
(A)
E
arth Leakage
Pro
tection
N
eutral Wire/
Live Wire
(Length
≤30m)
Ground
Wire
Capacity
Fuse
220~240VAC
≥1.5
≥1.5
20
15
30mA
B
elow 0.1 sec
50Hz
Fig.10
Photovoltaic function connection
Connection instructions are as follows:
(1) Remove 3 screws from the housing cover and lift up the housing cover.
(2)
Separate the connecting plugs between main control board and display, and then r
emove
the
housing cover.
(3) T
ake
the
p
hotovoltaic inverter connecting cable outside through the opening from which the
power cord come out and then connect it to the
p
hotovoltaic inverter.
(4) Connec
t
back
the
plugs between main control board and display, and then install back the
housing cover.
Housing cover
Photovoltaic inverter
connecting cable
Power cord
1.
2.
-10-
HTW-AT-O-
200
VA2
Model
Power
supply
Max. power input (under boost mode)
Max. current input (under boost mode)
Water inlet/outlet
Max
.
operating
pressure
Sound power level
Net
weight
Dimensions
220-240V~
50
Hz
2950W
12.8A
2000W
600W
R134a/900g
28
℃
~65
℃ (
default
53
℃)
-7
℃~43℃
2000W
28
℃
~75
℃
-15℃~43℃
2.4MPa/0.6MPa
0.8MPa
DN20
Degree
of
protection
Anti
-
electric
shock
class
IPX
4
Class
Ι
≤
6
0
dB(A)
Rated
capacity
200L
Φ
580
×1
910mm
Rated
heat output
Rated
power input
Refrigerant
Water
temp.
outlet
Operating temp. range
Rated
power input
Water outlet temp.
Operating temp. range
Max. operating
pressure for refrigerant
circuit (discharge side/suction side)
Heat pump
Electric heating
Air source heat pump water heater
98kg
Note (1):
Note (2):
tested with air duct, according
to
EN
12102-1-2017,
ISO
3744:2010.
The test conditions for rated
parameters
are
dry
-
bulb
temperature of 20
℃ ,
wet-bulb
temperature of 15
℃,
inlet water temperature of
10
℃,
outlet
water
temperature
of
5
3
℃,
according to
EN 16147:2017, (EU) NO 814-2013.
Sound power level
Storage tank
Solar energy inlet/outlet Without solar energy coil
Heat pump, assistance, automatic and boost mode
Operational mode
HTW-ATS-O-
200
VA2
L
Declared load profile
3.73
COP
DHW
156.8%
Energy efficiency
A++
Energy efficiency class
265.3L
Mixed
water
at
40
℃
Sewage outlet
DN20
Condensate
water
outlet
DN15
DN20
Gross
weight
108kg
88kg
98kg
(1)
(2)
■
Technical Parameters
ATTENTION
The parameters in the above table are only for reference. When the contents of this table differ
from those of the nameplate on the appliance, please refer to the nameplate.
Installation
Installation
40
Содержание HTW HTW-AT-O-200VA2
