manualshive.com logo in svg

GHM HONSBERG OMNIPLUS-F Series, Руководство по эксплуатации

Поделиться
Скачать
GHM HONSBERG OMNIPLUS-F Series Скачать руководство пользователя страница 7

 

 

OMNIPLUS-F 

Safety | 2 

C-E01_X__OMNIPLUS-F__DB2-1.0 

7/ 45 

2.3

  Safety instructions 

 

The product must be used in accordance with the technical data and the notes in 
these operating instructions. Technical data can be found in the respective valid prod-
uct data sheet (product information). 

 

 

 

 

 CAUTION 

 

Functional impairment 

Errors during installation, assembly or configuration of GHM products may impair the 
proper functioning of the subsequent process or lead to damage. However, serious 
hazards do not necessarily result directly from our products. 
-  Ensure proper and correct installation, assembly as well as programming and con-

figuration of the product! 

-  Provide independent safety measures!

 

-  Only allow settings to be carried out by qualified personnel!

 

 

 

 

 

 

 CAUTION 

 

Misbehavior! 

If it can be anticipated that the product can no longer be operated safely, it must be 
taken out of service and secured against further use by labeling. The safety of the 
user may be impaired by the device if, for example, it exhibits visible damage, no 
longer operates as specified or has been stored for a long time under unsuitable con-
ditions. 
-  Visual inspection! 

-  If in doubt, send the product to the manufacturer for repair or maintenance!

 

 

 

 

 

 

 CAUTION 

 

Temperature damage! 

Exposure of the product to a temperature not specified in the Technical Data chapter 
may cause errors, defects, or heat/frost damage. 
-  Take note of the temperature range! 

 

 

 

 

 

 CAUTION 

 

Overstressing! 

Failure to properly install and operate the product will result in a defect. 
-  Observe the tightening torque! 

-  Do not use as a fixed point!

 

-  Use filters for contaminated media!

 

 

 

 

 

 
 

 

 

 NOTE 

 

This product does not belong in children's hands! 

 

 

 

 

 

 

 

Содержание HONSBERG OMNIPLUS-F Series














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды