background image

 

PMsense 

-   15   -

 

V1.0

 

6

 

MODBUS-RTU PROTOCOL 

By  default,  the  instrument  has  MODBUS  address 

1

  and  communication  parameters 

19200, 8E1. The address and the communication parameters can be changed by using 
the appropriate serial commands of the proprietary protocol or, alternatively, directly 
with MODBUS commands by changing the value of the Coils and Holding Registers de-
scribed later. 

The MODBUS-RTU protocol, if set as the operating protocol (default), is active after 10 
seconds from the instrument power on. 

In  order  to  change  the  instrument  configuration  using  the  MODBUS-RTU  protocol,  the 
value 1 must be written first in the 

Coil

 number 2 (address 1). 

Below is the list of registers (the tables show both the number and the address of the 
registers,  with  the  address  of  the  register  equal  to  the  number  of  the  register  de-
creased by 1, as defined in the MODBUS standard). 

Input Registers: 

Number  Address 

Description 

Format 

PM1.0 in N° of particles/ml. 

Measurement updated according the operating mode set 
with the CPLS, CPLP and CPS commands.

 

16-bit Integer 

PM2.5 in N° of particles/ml. 

Measurement updated according the operating mode set 
with the CPLS, CPLP and CPS commands.

 

16-bit Integer 

PM10 in N° of particles/ml. 

Measurement updated according the operating mode set 
with the CPLS, CPLP and CPS commands.

 

16-bit Integer 

PM1.0 in µg/m

3

 (x10). 

Measurement updated according the operating mode set 
with the CPLS, CPLP and CPS commands.

 

16-bit Integer 

PM2.5 in µg/m

3

 (x10). 

Measurement updated according the operating mode set 
with the CPLS, CPLP and CPS commands.

 

16-bit Integer 

PM10 in µg/m

3

 (x10). 

Measurement updated according the operating mode set 
with the CPLS, CPLP and CPS commands.

 

16-bit Integer 

PM1.0 in N° of particles/ml. 

Measurement averaged over 10 s and updated every 
second. Available in continuous measurement mode. 

16-bit Integer 

PM2.5 in N° of particles/ml. 

Measurement averaged over 10 s and updated every 
second. Available in continuous measurement mode. 

16-bit Integer 

PM10 in N° of particles/ml. 

Measurement averaged over 10 s and updated every 
second. Available in continuous measurement mode. 

16-bit Integer 

10 

PM1.0 in µg/m

3

 (x10). 

Measurement averaged over 10 s and updated every 
second. Available in continuous measurement mode. 

16-bit Integer 

Содержание Delta OHM PMBsense-A



























Отзывы: