page 1 of 8
8350-3 Temperature Transmitter Instructions
CAUTION!
•
Remove power to unit before wiring
input and output connections.
•
Follow instructions carefully to avoid
personal injury.
+GF+ SIGNET 8350-3 Temperature Transmitter Instructions
ENGLISH
Contents
1. Installation
2. Specifications
3. Electrical Connections
4. Menu Functions
Temperature
Temp Units:
°
C
°
F
Relay 1
Relay 2
ENTER
1.1 Panel Installation
The Panel Mounting kits are supplied with the hardware to
install instrumentation into panels and maintain a NEMA 4X
watertight seal.
1.
Punch out panel and de-burr edges. Recommended
clearance on all sides between instruments is 1 inch.
2.
Place gasket on instrument, and install in panel.
3.
Slide mounting bracket over back of instrument until
quick-clips snap into latches on side of instrument.
4.
Connect wires to terminals.
5.
To remove, secure instrument temporarily with tape from
front or grip from rear of instrument. DO NOT RELEASE.
Press quick-clips outward and remove.
1.2 Integral Assembly (3-8052)
1.
Punch out conduit ports if necessary.
2.
Connect sensor to integral adapter. Push and twist-lock
integral adapter to conduit base and secure with locking
ring and screw.
3.
Mount unit in pipe. Route cable through cable gland and
connect to transmitter.
4.
Close unit and secure. Seal cable entry.
1.3 Universal Assembly (3-8050)
1.
Install transmitter base
2.
Connect wires to transmitter.
3.
Close unit and secure with push and twist lock.
Seal cable entry.
1.
Installation
The transmitter is available in three versions: a panel mount version, an integral (pipe mount) version, and a universal assembly for
installation near the sensor.
Standards and Approvals
•
CSA, CE, UL listed
•
Manufactured under ISO 9001
Electrical
Sensor Input: Range: -10 to 100
°
C
Current outputs (2):
•
4 to 20 mA, isolated, fully adjustable and reversible
•
Power: 12 to 24 VDC
±
10%, regulated, 60 mA max current
•
Max loop impedance: 50
Ω
max. @ 12 V, 325
Ω
max. @ 18 V
600
Ω
max. @ 24V
•
Update rate: 200 ms
•
Accuracy:
±
0.03 mA
Open-collector outputs (2 each): Hi, Lo, Pulse Programmable
•
Open-collector, isolated, 50 mA sink or source, 30 VDC max.
pull-up voltage
•
Hysteresis: User adjustable
2 . Specifications
General
Compatibility: +GF+ SIGNET 3-2350-1 or -2 Temperature
Sensors
Accuracy:
±
0.5
°
C
Enclosure:
•
Rating: NEMA 4X/IP65 front
•
Case: PBT
•
Window: Polyurethane coated polycarbonate
•
Keypad: Sealed 4-key silicone rubber
•
Weight: Approx. 325g (12 oz.)
Display:
•
Alphanumeric 2 x 16 LCD
•
Update rate: 1 second
•
Contrast: User selected, 5 levels
Environmental
Operating temperature: -10 to 70
°
C (14 to 158
°
F)
Storage temperature: -15 to 80
°
C (5 to 176
°
F)
Relative humidity: 0 to 95%, non-condensing
1
8
7
Internal open-collector
output circuit
Outputs
Isolation
15Ω
S
D
2
10
9
_
+
seal
seal
wires
quick-clip
gasket
panel
terminals
mounting
bracket
latch
transmitter
Liquid Tight
Connector
(cable gland)
B-1/00 English
3-8350.090-3
