GEZE TSA 325 NT страница 46 Скачать руководство пользователя

Страница: 46 / 112

Revolving door TSA 325 NT

Options

5.5.3 Set the adjustable pulley on the pulley holder

The more the tooth belt (3) lifts up from the pulleys on the pulley holder, the more the tooth belt tension will

fluctuate. Because of this, the adjustable pulley (1) must be set with the smallest possible distance (5) from the

passing driver (4) after installing the leaves on all pulley holders.

Adjustable pulley

Cylinder head screw

Toothed belt

Driver

Distance

Undo the cylinder head screw (2).

Push the adjustable pulley (1) so that the distance (5) between the adjustable pulley (1) and the tooth belt (3)

is as small as possible.

Re-tighten the cylinder head screw (2).

5.5.4 Turned and crossed tooth belts

To keep the tooth belt as quiet as possible, it must run across the largest possible number of pulleys with the flat

back of the belt.

min. 500

min. 200

Belt 1

Belt 2

Tooth belt turned by 180°

Driver in open position

Driver in closing position

Tandem roller

Содержание TSA 325 NT

















































































































Результаты поиска

Содержание TSA 325 NT

Отзывы:

Похожие инструкции для TSA 325 NT

Бренды по названию

Популярные бренды

GEZE TSA 325 NT, Руководство по установке

Результаты поиска

Содержание TSA 325 NT

Отзывы:

Похожие инструкции для TSA 325 NT

Бренды по названию

Популярные бренды