GEZE TSA 325 NT страница 100 Скачать руководство пользователя

Страница: 100 / 112

Revolving door TSA 325 NT

100

Revolving door TSA 325 NT, 3-leaf

Place the protective leaves on blocks so that the centre of the glass pane is elevated.

The straight glass edges must be freely accessible.

Mounting the brush strip

Spread suitable synthetic glass glue into

the long groove for the brush strip (1).

Stick the brush strips (1) flush with the

long edges of the glass.

Mount the locking mechanism (X) to the glass leaf

Mount the top part of the locking mechanism:

Push the locking bolts (2) into the brackets (3) for the

manual locking device.

Screw the lift pin (5) into the locking bolts (2).

Screw the spring force pin (4) into the screw channel

on the floor until the locking bolts (2) snap fully into

both end positions.

Clip the protective cover (1) in place.

Содержание TSA 325 NT

















































































































Результаты поиска

Содержание TSA 325 NT

Отзывы:

Похожие инструкции для TSA 325 NT

Бренды по названию

Популярные бренды

GEZE TSA 325 NT, Руководство по установке

Результаты поиска

Содержание TSA 325 NT

Отзывы:

Похожие инструкции для TSA 325 NT

Бренды по названию

Популярные бренды