GESTRA NRA 1-3 Скачать руководство пользователя

Страница: 17 / 32

Operation, alarm and test

Mode 1, 6:

After the mains voltage has been switched on and the display test has been finished the

system temperature, error messages and current alarms will be indicated.

Mode 2 to 5 and 7:

After the mains voltage has been switched on and the display test has been

finished error messages and current alarms will be indicated.
For more information on the codes HIS, Int and tSt see section “Alarm list, Maintenance interval and

Test”, mode 1 to 7 (page 23).

Start

For the communication with the CAN bus each bus node requires an own address (node ID) and baud

rate (speed of data transfer) setting.
The cable length between the bus nodes dictates the baud rate setting.

Cable length

Baudrate

125 m

250 kBit/s (factory setting)

250 m

125 kBit/s

335 m

100 kBit/s

500 m

50 kBit/s

1000 m

20 kBit/s

Please make the following settings:
Briefly press the E key and then key 1 until CAN is indicated on the seven-segment display. Enter the

baud rate and node ID settings.
For the node ID you can use numbers between 1 and 127.

If the baud rate and/or the node ID settings are changed the new values will only become active after

switching the power supply voltage to the test station off and on again.

Only for NRA 1-3 CAN: Setting node ID and baud rate

Start

Press key E

briefly

→

←

longer

HIS

Keys

(1)

↓

(3)

↑

CAN

Press key E

briefly

→

←

longer

Press key E

briefly

→

←

longer

Change

indi-

cation

keys (1),(3)

Press key

E briefly

→

don

←

CAN

Keys

(1)

↓

(3)

↑

Press key E

briefly

→

←

longer

Change

tem-

perature

keys (1),(3)

Press key

E briefly

→

don

←

- continued -

Содержание NRA 1-3

































Результаты поиска

Содержание NRA 1-3

Отзывы:

Похожие инструкции для NRA 1-3

Бренды по названию

Популярные бренды

GESTRA NRA 1-3, Оригинальная инструкция по установке

Результаты поиска

Содержание NRA 1-3

Отзывы:

Похожие инструкции для NRA 1-3

Бренды по названию

Популярные бренды