background image

HP-BLU User Manual 

Revision 1.0 

21 

 

Test Name 

Standards 

Test Specifications 

Minimum 

Performanc

e Criterion 

Required 

EUT 

Serial 

Number 

Results 

Surge Immunity 
IEC61000-4-5 (2014) 

Power: ±2kV L-PE / ±1kV L-

I/O Ports: ±1kV / N/A 
Communication Ports: ±1kV / 
N/A 

Labcem#2340 

Pass 

Labcem#2341 

N/A 

Immunity to Conducted Disturbances, 
Induced by Radio-Frequency Fields 
IEC61000-4-6 (2013) 

Power: 3V 
I/O Ports: N/A 
Communication Ports: N/A 

Labcem#2340 

Pass 

Labcem#2341 

N/A 

Power Frequency Magnetic Field 
Immunity 
IEC61000-4-8 (2009) 

Continuous Field: 30A/m / 
50Hz & 60Hz 

Labcem#2340 

Pass 

Labcem#2341 

Pass 

Voltage Dips, Short Interruptions and 
Voltage Variation Immunity on AC 
Input 

IEC61000-4-11 (2004) 

Voltage dips: 0%Un during 1 
cycle 

Labcem#2340 

Pass 

Voltage dips: 40%Un during 
10 cycles (at 50 Hz) 

Labcem#2340 

Pass 

Voltage dips: 40%Un during 
12 cycles (at 60 Hz) 

Labcem#2340 

Pass 

Voltage dips: 70%Un during 
25 cycles (at 50 Hz) 

Labcem#2340 

Pass 

Voltage dips: 70%Un during 
30 cycles (at 60 Hz) 

Labcem#2340 

Pass 

Short interruptions: 0%Un 
during 250 cycles (at 50 Hz) 

Labcem#2340 

Pass 

Short interruptions: 0%Un 
during 300 cycles (at 60 Hz) 

Labcem#2340 

Pass 

 

Table 8 

Performance criteria  

Performance 

Criteria

 

Description

 

Criteria A

 

The DUT does not have any noticeable deviations in its performance before, during or after 
the application of the EMC test. 

If  a  range  of  performance  is  specified  as  normal  operation,  the  DUT  did  not  have  any 
readings outside of this range before, during or after the application of the EMC test. 

Criteria B 

The DUT does not have any deviations of performance before or after the application of the 
EMC  test,  but  during  the  application  a  deviation  is  noted  that  is  not  considered  normal 
operation. When the EMC test is paused or completed the DUT recovered on its own and 
did not require any user intervention to return it to normal operation. 
If  a  range  of  performance  is  specified  as  normal  operation,  the  DUT’s  performance  was 
outside of this range during the application of the test, but recovered on its own and operated 
within its normal range after the application of the EMC test. 

No permanent damage occurred to the DUT or any AE as a result of the disturbance. 

Содержание HP-BLU Series





























Отзывы: