14
Fig. 3
햲
ENGLISH
8 MEMORY STORING THE RADIO CODE
The control board has an integrated 2-channel decoding
system. This system makes it possible to memory-store both
total opening (OPEN A) and partial opening OPEN B) of the
automated system - this is made possible by an additional
receiver module (fig.3 ref.
햲
) and radio controls on the same
frequency.
Only one radio code can be used at a time.
To change over from one code to another, you
must delete the existing one (see paragraph
on deletion), and repeat the memory-storage
procedure.
8.1 MEMORY STORAGE OF 868 RADIO CONTROLS
A maximum of 250 codes can be memory
stored, split between OPEN A and OPEN B.
On the radio control, simultaneously press and hold down
push-buttons P1 and P2.
The radio control LED begins to flash.
Release both push-buttons.
Press the LOGIC (SW3) or SPEED (SW2) push-button, to
memory store respectively total opening (OPEN A) or partial
opening (OPEN B), and as you hold it down, also press the
SETUP (SW1) push-button. The relevant LED starts to flash
slowly for 5 sec.
Release both push-buttons.
Within these 5 sec., while the radio control LED is still flashing,
press and hold down the required push-button on the radio
control (the radio control LED lights up on steady beam).
The LED on the board lights up on steady beam for 1
second and then goes OFF, indicating that storage was
executed.
Release the radio control push-button.
Quickly press twice the memory stored radio control push-
button.
The automated system performs one opening
operation. Make sure that the automated
system is free of any obstacle created by
persons or things.
To add other radio controls, transfer the code of the memory-
stored push-button of the radio control to the relevant push-
button of the radio controls to be added, observing the
following procedure.
On the memory stored radio control, simultaneously press
and hold down push-buttons P1 and P2.
The radio control LED begins to flash.
Release both push-buttons.
Press the memory stored push-button and hold it down
(the radio control LED lights up on steady beam).
Bring the radio controls near, press and hold down the
1.
2.
3.
4.
5.
6.
7.
8.
9.
•
•
•
•
•
7.2 MEMORY STORAGE OF BUS ACCESSORIES
You can add the BUS photocells to the system at any time,
simply by memory-storing them on the board, observing the
following procedure:
Install and program the accessories using the required
address (see paragraph 7.1)
Cut power to the board.
Connect the two accessories cables to the red terminal-
board J10 (any polarity will do).
Power up the board, taking care to first connect the
main power supply (transformer output) and then any
batteries.
Quickly press once only the SW1 (SETUP) push-button, to
execute learning. The BUS LED flashes.
Give an OPEN A impulse, leaves will move and the BUS
learning procedure is over.
The board has memory stored the BUS accessories. Follow the
instructions in the table below to check if the BUS connection
is correct.
Tab. 4 - Description of BUS LED
Steady light
Normal operation (LED ON even in the
absence of photocells)
Slow flashing
lamp
(flash
every 0.5 sec)
At least one input engaged: photocell
engaged or not aligned, Open A or Open
B or Stop input engaged
Light OFF
(flash every 2.5
sec)
BUS line short circuited
Fast flashing
lamp
(flash
every 0.2 sec)
If you have detected a BUS connection
error, repeat the acquisition procedure. If
the error is repeated, make sure that there
is not more than one accessory with the
same address in the system (also see the
accessories instructions)
1.
2.
3.
4.
5.
6.
Содержание BRAIN 06 24V
Страница 1: ...BRAIN 06 24V...
