Geneva XS, Инструкция по эксплуатации

Страница: 4 / 34

English
6 5
Why is my mobile phone not connecting?
You will find more detailed information
on various mobile phones on the Support
pages at www.genevalab.com.
The Model XS will not turn on, the display
shows “low” and “batt”.
“low” and “batt” means low battery.
Connect the power adapter to the Model
XS and the battery will begin charging.
You can use the Model XS within a few
minutes.
The Model XS will not turn on,
nothing happens.
If the battery is very low, there is too
little power to turn on the display, even if
the power adapter is connected. Model
XS can be turned on after it has been con-
nected for a few to the power adapter.
Why is the Model XS turning off after
a while?
After one minute the device
will automatically turn itself
off, when it is not in the
correct position ( see figure
in “Turning the Power On” ).
The Model XS does not
turn on when i touch the button.
Touch with one finger only. Don’t touch
the rest of the touch panel with other
fingers. The touch panel works properly
when used with one finger only.
How do the Bluetooth settings look like
in the iphone
®
?
What is the pin for a Bluetooth
connection?
The PIN is: 0000 ( 4 zeros ). Not all comput-
ers or mobile phones require a pin code
during the initial setup ( pairing ).
i have an unreliable connection with
dropouts when listening via Bluetooth.
• Move the mobile phone closer to the
Model XS.
• Move away or turn off other wireless
devices that can disturb a Bluetooth con-
nection ( for example WLAN / Wifi, other
mobile phones etc. ).
How do i know if the battery is charging?
A small dot on the lower right of the
display blinks slowly if the battery is
being charged.
How can i check the battery charge?
A dot on the lower right corner of
the display shows the battery status:
• On: battery fully charged.
• Blinking: battery is charging.
If the battery is low, the display will also
show “low” and “batt”. In this case the
Model XS will automatically turn off, but it
still has enough power to show the time
for a while.
Why is the alarm not working when the
case is closed?
The alarm does not work in this position
because the device power is off. However,
the clock is still running.
SUppORT
More information, troubleshooting, etc.
Select “Support” at www.genevalab.com.
Service and Repair
If the product is damaged and needs
repair, please contact your dealer. Visit
www.genevalab.com to find a dealer in
your area.
Warranty
See the specific terms for your country at
www.genevalab.com.
Bluetooth
Mobile phones and computers with
Bluetooth can connect to the Model
XS and play music. The mobile
phone or computer must support
Bluetooth A2DP.
Initial Setup ( “pairing” ) With iPhone
®
1. Touch the key until the display
shows “Blue”. Wait for 20 seconds
until the display shows a blinking “P”.
2. Select “settings” on your iPhone ® .
Select “General / Bluetooth”. Turn
on Bluetooth. New Bluetooth
devices are discovered automati-
cally. After a few seconds “Geneva
XS Sound System ( Not Paired )”
will appear.
3. Select “Geneva XS Sound System”.
The phone is now connecting
( “pairing” ) to the Model XS.
4. If the phone asks for a PIN: enter
“0000” ( four zeros ).
5. Now you can play music on an
iPhone
®
App “iPod” and listen to it
on the Model XS.
playing Music
Most phones connect automatically
to the Model XS after the initial setup
( “pairing” ).
1. Touch the key on your Model
XS until the display shows “Blue”.
When Model XS connects, the dis-
play shows “C” for a few seconds.
2. Play music on the mobile phone,
music will start playing on Model XS
automatically after a few seconds.
pairing guides for other devices
and mobile phones Go to www.
genevalab.com and select “Support.”
Status information on the display
S: Searching for prevousliy paired
devices.
C: Connection successful.
p:
Pairing. If Model XS did not make
a successful connection within 20
seconds, Model XS will go into the
pairing mode for 2 minutes.
Setting the Alarm
1. Turn on Model XS, then touch : a
blinking “A” appears on the display.
2. Set the desired alarm time using
and .
3. Touch again to save the alarm
time. “A” indicates alarm is now on.
4. Touch to turn Model XS off.
Turning the Alarm On And Off
Turn off Model XS, then touch any
key on the touch panel to toggle the
alarm. “A” on the display indicates
the alarm is on.
Muting the Alarm
Touch any key on the touch panel to
mute the alarm. The alarm will auto-
matically turn off after 20 minutes if
no key on the touch panel is touched.
Selecting the Alarm Sound
There are two alarm sounds: FM radio
and a beeping sound. If you set the
alarm and the current mode is FM,
the FM radio will play when the alarm
goes off. Otherwise the beeping
sound is used.
Setting the Clock
1. Turn on Model XS, then touch .
The letter “C” starts blinking on
the display.
2. Use and to set the current time.
3. Touch to complete the procedure.
AM / pM Display ( US version Only )
The dot to the right of the minute
digits indicates AM or PM:
• Off: AM
• On: PM
TROUBLESHOOTing ALARM
Settings on iPhone
®
Playing music with App “iPod”