manualshive.com logo in svg

Genesys GEN10-330, Руководство пользователя, Страница: 73 / 82

Поделиться
Скачать
Genesys GEN10-330 Скачать руководство пользователя страница 73

64

NOTE

SW1 position 3 and 4 must be in their Up position for operation

with 4-20mA Isolated Programming and Monitoring.

CAUTION

To prevent damage to the unit, do not program the output voltage and current

to higher then the power supply rating.

Perform the following procedure to configure the power supply:

1. Turn the power supply AC power switch to Off.

2. Connect a short between J1-8 and J1-12 (refer to Table 4-4).

3. Set Setup switch SW1-1 to its UP position for Output Voltage external programming

and SW1-2 to its UP position for Output Current limit external programming.

4. Set SW1 position 3 to select the programming voltage range: Down=0-5V, Up=0-10V.

5. Set SW1 position 4 to select the monitoring range: Down=0-5V, Up=0-10V.

6. Ensure that SW1 positions 7 and 8 are in the their down position.

7. Connect the programming sources to the mating plug of the Isolated Programming

connector. Observe for correct polarity of the voltage source.

8. Set the programming sources to the desired levels and turn the power supply ON.

Perform the following procedure to configure the power supply:

1. Turn the power supply AC power switch to Off.

2. Connect a short between J1-8 and J1-12 (refer to Table 4-4).

3.Set setup switch SW1-1 to its UP position for Output Voltage external programming and

SW1-2 to its UP position for Output Current limit external programming.

4. Set SW1 position 3 to it's Up position.

5. Set SW1 position 4 to it's Up position.

6. Ensure that SW1 positions 7 and 8 are in their Down position.

7. Connect the programming source to the mating plug of the Isolated Programming

connector. Observe for correct polarity of the voltage source.

8. Set the programming sources to the desired levels and turn the power supply ON.

8.4.2 Setting up the power supply for 4-20mA Isolated Programming and Monitoring

8.4.1 Setting up the power supply for 0-5/0-10V Isolated Programming and Monitoring

8.4 SETUP AND OPERATING INSTRUCTIONS

J1-8 and J1-12 must be shorted together with a jumper.

NOTE

J1-8 and J1-12 must be shorted together with a jumper.

NOTE

64

Содержание GEN10-330



















































































Отзывы:

Нет отзывов