Genesis Razer X Скачать руководство пользователя страница 41

Страница: 41 / 64

Genesis GRX 41

PRIMARY AND SECONDARY BLADES

Blade Gap

After each blade rotation, shim the lower blades to keep the gap within the specifications listed in

the table below. Do not shim the upper blades. Use only Genesis shim kits.

Blade Gap Measuring Procedure

Slowly close jaws until blades begin to bypass. Stop the jaw and check the gap with a feeler

gauge.

Cycle the jaws slowly and continue checking the gap at several points along the entire length of

the blades.

Note: The gap will be consistent along the entire length of the blades if they have been rotated

and shimmed correctly.

If the blade gap exceeds the maximum listed on the table

above, shim the lower blades. Blades must be replaced when

shims exceed 0.060”.

Shimming

Loosen blade bolts.

Install shims between the blades and adjustment plates as

needed to bring into tolerance.

Torque bolts to spec and recheck the tolerances.

Do not use more than 0.060” of shims.

Install shims

Adjustment plates

Blades

Cutting Blade Gaps

Model

Minimum

Maximum

195 - 395

0.005”

0.015”

Blade Gap Locations

Содержание Razer X

































































Результаты поиска

Содержание Razer X

Отзывы:

Похожие инструкции для Razer X

Бренды по названию

Популярные бренды

Genesis Razer X, Инструкция по безопасности и эксплуатации

Результаты поиска

Содержание Razer X

Отзывы:

Похожие инструкции для Razer X

Бренды по названию

Популярные бренды