General Standards Corporation PCI-SIO4 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 66

background image

PCI-SIO4 User Manual

General Standards Corporation

8302A Whitesburg Drive Huntsville, AL 35802, Phone: (256) 880-8787

39

CHAPTER 3: PCI INTERFACE

3.0

PCI INTERFACE REGISTERS

A PCI9080 I/O Accelerator from PLX Technology handles the PCI Interface. The PCI interface is compliant
with the 5V, 33MHz PCI Specification 2.1. The PCI9080 provides dual DMA controllers for fast data
transfers to and from the on-board FIFOs. Fast DMA burst accesses provide for a maximum burst
throughput of 132MB/s to the PCI interface. To reduce CPU overhead during DMA transfers, the controller
also implements Chained (Scatter/Gather) DMA, as well as Demand Mode DMA.

Since many features of the PCI9080 are not utilized in this design, it is beyond the scope of this document to
duplicate the PCI9080 User’s Manual. Only those features, which will clarify areas specific to the PCI/PMC-
HPDI32, are detailed here. Please refer to the PCI9080 User’s Manual (See Related Publications) for more
detailed information. Note that the BIOS configuration and software driver will handle most of the PCI9080
interface. Unless the user is writing a device driver, the details of the PCI interface (Chapter 2) may be
skipped.

3.1

PCI CONFIGURATION REGISTERS

The PCI device configuration for the PCI/PMC-HPDI32 is fully PCI 2.1 compliant. Table 3.1-1 contains a list
of the PCI configuration registers present in the PCI9080. An on-board configuration serial EEPROM
initializes many of these registers.

Table 3.1-1:

PCI Configuration Registers

PCI

CFG

Addr

Local

Offset

Addr

PCI/Local

Writable

Register Name

Value after

Reset

0x00

0x00

Local

Device ID/Vendor ID

0x908010B5

0x04

0x04

Y

Status/Command

0x02800017

0x08

0x08

Local

Class Code/Revision ID

0x0680003

0x0C

0x0C

Y[15:0],

Local

BIST (Unused)/Header Type/Latency Timer/Cache Line Size

0x00002008

0x10

0x10

Y

PCI Base Addr 0 for Memory Mapped Local/Runtime/DMA
Registers (PCIBAR0)

0x00000000

0x14

0x14

Y

PCI Base Addr 1 for I/O Mapped Local/Runtime/DMA Registers
(PCIBAR1)

0x00000001

0x18

0x18

Y

PCI Base Addr 2 for Local Addr Space 0 (PCIBAR2)

0x00000000

0x1C

0x1C

Y

PCI Base Addr 3 for Local Addr Space 1 (PCIBAR3) (Unused)

0x00000000

0x2C

0x2C

Local

Subsystem ID/Subsystem Vendor ID

0x90802400

0x30

0x30

Y

PCI Base Address to Local Expansion ROM (Unused)

0x00000000

0x3C

0x3C

Y[7:0],

Local

Max_Lat/Min_Gnt/Interrupt Pin/Interrupt Line

0x00000100

«
...
44
45
46
47
48
...
»

Содержание PCI-SIO4



































































Отзывы:

Нет отзывов

Похожие инструкции для PCI-SIO4

Interflex IF-73

Бренд: Allegion Страницы: 9

Бренд: Vantec Страницы: 8

Бренд: Sangoma Страницы: 6

Бренд: TEDIA Страницы: 2

Creative Sound Blaster PCI

Бренд: Creative Technologies Страницы: 17

Бренд: Farpointe Data Страницы: 2

CONEKT PCR-620L-OSDP

Бренд: Farpointe Data Страницы: 2

Бренд: AEG Страницы: 39

Бренд: AEG Страницы: 36

Бренд: AEG Страницы: 50

Бренд: AEG Страницы: 33

Бренд: Omega Страницы: 66

Бренд: ZKTeco Страницы: 7

UHF10F Pro Reader

Бренд: ZKTeco Страницы: 25

FusionHDTV 7 Cool

Бренд: Dvico Страницы: 46

Бренд: Alpha Страницы: 14

Бренд: KTI Networks Страницы: 1

Бренд: MIWA LOCK Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды