General Pump KF Series Скачать руководство пользователя страница 10

Страница: 10 / 31

Page 10

8. PORTS AND CONNECTIONS

KF Series pumps (see fig. 4) are provided with:

1. 2 inlet ports “IN”, 1” NPT-F

The line can be connected to either of the two inlet ports; the one not being used must be hermetically sealed.

2. 2 outlet ports “OUT”, Ø 1/2” NPT-F

3. 3 auxiliary ports; used for the pressure gauge only

9. PUMP INSTALLATION

9.1 Installation

The pump must be installed in a horizontal position using the correct threaded feet M 16 x 1.5; fasten the screws with a

torque value of 154.8 ft. lbs. (210 Nm).. The base must be perfectly flat and sufficiently rigid in order to avoid bending and

misalignments on the pump/transmission coupling axis due to the torque applied during operation. The unit must not be

rigidly fixed to the pavement, but requires the use of anti-vibration elements. For special applications contact the

Customer

Service Department

The pump is equipped with two lifting eyebolts to facilitate installation, as shown in the following figure.

In case of disassembly, to avoid allowing debris inside the front part of the crankcase, close the threaded hole with

the threaded cap.

GENERAL PUMP

A member of the Interpump Group

KF SERIES

Serial #10127003 and later

Ref 300763 Rev. F

08-21

Содержание KF Series
































Результаты поиска

Содержание KF Series

Отзывы:

Похожие инструкции для KF Series

Бренды по названию

Популярные бренды

General Pump KF Series, Руководство пользователя

Результаты поиска

Содержание KF Series

Отзывы:

Похожие инструкции для KF Series

Бренды по названию

Популярные бренды