background image

18. SPECIAL VERSIONS

GENERAL PUMP

A member of the Interpump Group

KFR SERIES

The KF pump is also available in the special Version:

•  KFR

The following information is helpful in deciding how to choose and use this pump version.

Unless specified, observe the above instructions for the standard KF pump. 

18.1 KFR Pump 

18.1  KFR Pump
18.1.1 Operating Instructions

The KFR series pump has been designed to operate in environments with atmospheres that are not potentially 

explosive and for using water rich in particulate, therefore it is considered ideal for system with fluid recirculation. 

The durability of the piston seal is directly in relation to the percentage of the presence of solids in the fluid as 

regards both their size and their density. 

For a long seal life we recommend a particulate grain size of no more than 200 micron and 20% max. in volume.

For more information and general system layout see par. 9.7.

18.1.2 Water Temperature

The maximum water temperature is 104° F (40° C). However, the pump can be used with water temperatures 

up to 140° F (60° C), but only for short periods. In this case it is best to contact our 

Technical or Customer 

Service Department. 
18.1.3 Maximum Pressure and Flow Rate

The rated specifications stated in our catalog are the maximum that can be obtained by the pump. Independently 

of the power used, the maximum pressure and RPM indicated on the specification label can never be exceeded 

unless prior authorization given by our 

Technical or Customer Service Department.

18.1.4 Minimum Operating Speed

The minimum permissible speed of the crankshaft for these types of pumps is 100 RPM; any RPM other than as 

shown in the performance table (see par. 18.1.5) must be authorized by our 

Technical or Customer Service 

Department. 

18.1.5  Technical Features

Model

RPM

Flow Rate

Pressure

Power

GPM

I/min

PSI

bar

HP

kW

KFR20A

1000

24.5

93

3045

210

50

37

KFR30A

1000

28

106

2900

200

55

40

KFR32A

1000

31.7

120

2610

180

56

41.2

KFR36A

800

32.2

122

2300

160

50

37

900

36.2

137

2050

140

50

37

1000

40

153

1900

130

52

38.2

KFR40A

900

45

170

1595

110

49

36

18.1.6 Dimensions and Weight

Dry weight 150 lbs. (68 kg.)

Page 27

Serial #10127003 and later

Ref 300763 Rev. F 

08-21

Содержание KF Series
































Отзывы: