General Pipe Cleaners Flexi-Rooter 100, Руководство по эксплуатации

Страница: 6 / 12

Flexi - Rooter 100
®
Catalog #
Shaft
Length For Pipe Size Typical Applications
50FR1A 50 ft.
(15.2 m)
2” to 4”
(50 – 100mm)
Medium and large lines.
For clearing roots, de-
scaling pipes, and
clearing grease and soft
blockages.
25FR1A 25 ft.
(7.6m)
2” to 4”
(50 – 100mm)
Flexible shaft exten-
sion. Can be added to
50 ft. shaft to clear lines
up to 75 ft. long.
Flexible Shaft Application Chart - 5/16” (8mm) (Table 1)
Catalog # Description
Leader
Length Typical
Applications
FR-1-1/2CG* 1- 1/2”
ClogChopper
Cutter
1- 1/4” Penetrating cutter.
Allows chain cutter
to get through
clogged lines.
FR-2CK* 2” Chain
Cutter -
Double Chain
– Adjustable
3- 7/8” For PVC and Soft
stoppages
FR-2CCK 2” Carbide
Tipped Chain
Cutter -
Double Chain -
Adjustable
3- 7/8” Removing Roots
and Descaling.
(Do not use in PVC)
FR-3-4CK 3” – 4” Chain
Cutter -
Triple Chain
–
Adjustable
7- 3/8” For PVC and Soft
stoppages
FR-3-4CCK* 3” – 4” Carbide
Tipped Chain
Cutter -
Triple Chain -
Adjustable
7- 3/8” Removing Roots
and Descaling.
(Do not use in PVC)
FR-3TAZ 3” Circular
Carbide
Tipped Chain
1- 1/4” For Descaling
(Do not use in PVC)
FR-4TAZ 4” Circular
Carbide
Tipped Chain
1- 1/4” For Descaling
(Do not use in PVC)
Cutter Application Chart for 5/16” (8mm) Flexible Shaft
(Table 2)
*Included in FR100-CS Cutter Set
ATTACHING CUTTERS TO A LEADER
Note: See the Cutter Application Chart to select the appropriate lead-
er to use with each cutter.
Caution: Carbide tipped chains can damage plastic. Use caution if
the clay pipe is broken or fragile. Use carbide tipped chain only in
metal pipes.
Note: Use the supplied Loctite
®
any time the set screws in a cutter are
tightened onto a leader. Never use permanent thread locker. See
manufacturer's website for proper use.
1. Before attaching leaders, chains or cutters, always be sure the
machine is turned OFF and unplugged.
2. Inspect the leader for damage. DO NOT use a leader it is dam-
aged.
3. Loosen the set screws in the cutter so that the leader will pass
through.
4. Proceed to the appropriate section for the cutter you are attaching.
ATTACHING CUTTERS TO A LEADER
CONT
.
For Adjustable Chain Cutters (FIGURE 2)
1. Slide the chain cutter and leader protector (when applicable) onto
the leader.
2. Slide one end of the chain cutter until it is flush with the end of the
leader and tighten the set screws.
3. While keeping the chains from twisting, slide the opposite end the
of the chain cutter closer to or further away from the other end in
order to achieve the desired cutting size and tighten the set
screws.
4. Ensure that at least 1/2" of shaft is exposed beyond the end of the
chain cutter.
6
FIGURE 2