manualshive.com logo in svg

Generac Power Systems R-200, Техническое руководство

Поделиться
Скачать
Generac Power Systems R-200 Скачать руководство пользователя страница 15

  

13

10A, 12VDC BATTERY CHARGER

Nominal Input AC Line Voltage  ........................ 120Vac
Operating AC Line Voltage Range ......108Vac to 132Vac
Input AC Line Frequency .............................50 or 60Hz
AC Line Fuse ...................................... 5 Amp, 5x20mm, 

Littelfuse P/N 218005

Battery Fuse ..............................15 Amp, Littelfuse ATO

Blade P/N 257015

Nominal Charge Rate ..................................... 10 Amps
Equalize Voltage (typ) ....................................13.8 Volts
Float Voltage (typ) .........................................13.0 Volts
Current at Equalize to Float Transition (typ)  .. 5 Amps
Battery Undervoltage Shutdown (typ) ...............11 Volts
LED Indicators
 

AC Line Voltage > 108Vac ...............Green LED ON

 

Battery Connected & Charging ........Yellow LED ON

 

the Green LED must be ON to obtain a valid
battery charging indication, 

 

Yellow LED ON if charge current > approx 2 
Amps)

Battery Current Drain (AC Power OFF) ....... 30mA (typ)
AC Line Connections ......................... via terminal block 

(AC Hot, AC Neut & GND)

Battery Connections .......................... via terminal block

(Pos +, Neg -)

Control Connections ......................AC Power Fail Relay, 

Form C, 2Amps, 12Vdc

(N.O. Contact closes when ac line voltage is applied)
(N.O. Contact opens when ac line voltage is removed)

‹

General Information

R-panel Technical Manual

Содержание R-200

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды