manualshive.com logo in svg

Generac Power Systems MGG155, Руководство по эксплуатации

Поделиться
Скачать
Generac Power Systems MGG155 Скачать руководство пользователя страница 55

Troubleshooting

35319 C

MGG155/210 Operating Manual

51

MPR Pmains IDMT 

Indicates overload IDMT protection activation. Overload IDMT protection is inverse defi-
nite minimum time protection which is based on the mains power. Protection reaction 
time depends on mains power value. High mains overload means short reaction time 
whereas low mains overload means longer reaction time. 
This protection is active if the 

Mns2POvrldProt 

setpoint is set to ENABLED. Protection is 

based on setpoints 

Mains protect

: 

OverldStrtEval 

and 

2POverldStEvDel. 

BOR PbusL IDMT 

Indicates overload IDMT protection activation. Overload IDMT protection is inverse defi-
nite minimum time protection which is based on the left bus power. Protection reaction 
time depends on the left bus power value. High left bus overload means short reaction 
time whereas low left bus overload means longer reaction time. 
This protection is active if the 

BusL2POvrldProt 

setpoint is set to ENABLED. Protection 

is based on setpoints 

BusL protect

: 

OverldStrtEval 

and 

2POverldStEvDel. 

BOC NCB fail 

NCB fail is detected if the 

NeutralCB fdb 

input doesn't follow 

Neutral CB C/O 

output 

within 400 ms. 

Wrn BadPwrCfg 

Power format is set differently in controllers which are part of the same control group. 
Check Power formats setting in GenConfig on the Miscellaneous card (available in the 
Advanced mode only).

WrnTstOnLdFail 

This alarm is issued if the Test on load function is activated (by closing corresponding BI) 
and genset is not able to take over mains load completely (mains import = 0) within the 

Sync/Load ctrl

: 

Load ramp 

time. Message “WrnTstOnLdFail” is recorded into controller 

history in case of this failure. It is either necessary to extend the 

Load ramp 

time or check 

engine speed regulation.

Wrn SpdRegLim 

This alarm indicates that controller Speed governor output has reached its limit. Warning 
is issued if Speed governor output stays close to one of the limit values for more than two 
seconds. Close to one of the limits means that Speed governor output value is within 
SpeedGo0,2V range or SpeedGovHiLim-0,2V range. 
This alarm gives you information that engine speed governor is either connected in a 
wrong way or one of the speed control related regulation loops6 is set in a wrong way. 
Warning is blocked if binary output functions SPEED up and SPEED down are config-
ured. 
Refer also to 

Sync/load control.

Wrn VoltRegLim 

This alarm indicates that controller AVRi output has reached its limit. Warning is issued if 
the AVRi output stays close to 0% or 100% limit for more than two seconds. Close to limit 
means that AVRi output value is either <2% or >98%. 
This alarm gives you information that generator voltage regulator is either connected in a 
wrong way or one of the voltage control related regulation loops is set in wrong way. 
Warning is blocked if binary output functions AVR up or AVR down are configured. 
Refer also to 

Volt/PF control adjustment 

chapter in an IGS-NT-x.y-Reference Guide.

G L neg8 

Generator phase is inverted. Check generator phases connection, one of generator 
phases is connected the other way round (swap generator coil leads connection). 

G ph+L neg8 

Wrong generator phases sequence, additionally one phase is inverted. 

G ph opposed8 

Wrong generator phases sequence. 

M L neg9 

Mains phase is inverted. Check mains transformer phases connection, one of trans-
former phases is connected the other way round (swap transformer coil leads connec-
tion). 

M ph+L neg9 

Wrong mains phases sequence, additionally one phase is inverted.

Table 8 - Digital Controller List of Alarms

NT

Alarm/History

Record

Description

Discount-Equipment.com

Содержание MGG155




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды