manualshive.com logo in svg

Generac Power Systems MGG155, Руководство по эксплуатации

Поделиться
Скачать
Generac Power Systems MGG155 Скачать руководство пользователя страница 37

Maintenance

32

MGG155/210 Operating Manual

35319 C

Check the level on the oil level regulator sight glass. The oil level should be about halfway up the sight glass when 
the engine is running. If not, adjust the regulator height by loosening the two screws on the regulator bracket and 
slowly sliding the regulator along the slots until the oil is at the proper level. Tighten the screws.

Figure 16 - Oil Level Sight Glass

This unit is equipped with an auxiliary engine oil reservoir. The level in the reservoir should be checked periodically 
and oil added as needed. Verify the reservoir valve is open to allow oil to drain into the oil level regulator. Close the 
valve before moving the unit. 

To check the engine oil using the dipstick:

1. Locate the engine oil dipstick. See 

Component Locations

.

2.

The most accurate oil level readings are measured when the engine is cold. If the engine was running, wait 

at least ten minutes before proceeding.

3.

Remove the dipstick and wipe it dry with a clean, lint free cloth.

4.

Slowly insert the clean dipstick into the tube. Visually confirm the dipstick is fully seated in the dipstick tube. 

A visual inspection is required because some dipsticks will require more effort than others to fully seat.

5.

After ten seconds, remove the dipstick and look at the oil level on both sides. The lower of the two readings 

will be the correct oil level measurement.

6.

Add oil (if necessary) to adjust the level. After adding or changing the oil, the engine should run for one min-

ute before checking the oil level. Remember to wait ten minutes to allow the engine to cool and oil to fully 
drain into the oil pan.

Typical causes of inaccurate oil level readings:

•

Reading the high level of the dipstick.

•

Reading the dipstick before the oil fully drains into the oil pan.

•

Inserting and removing the dipstick too quickly.

•

The dipstick is not fully seated in the dipstick tube.

Changing the Oil

Note: 

When changing oil, it is not necessary to drain the oil from the reservoir. 

1. Close the valve below the oil reservoir.

2.

Place a container below the oil drain port, located on the left side of the skid frame. Remove the oil drain 

plug with an Allen head wrench.

3.

Open the drain valve at the engine oil pan. Verify the oil level regulator valve is open.

4.

Allow the oil to drain completely into the container.

00573

Discount-Equipment.com

Содержание MGG155




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды