manualshive.com logo in svg

Generac Power Systems MGG155, Руководство по эксплуатации

Поделиться
Скачать
Generac Power Systems MGG155 Скачать руководство пользователя страница 54

Troubleshooting

50

MGG155/210 Operating Manual

35319 C

Mains Avg x >V 

If the value of 10 min. average mains voltage of any phase (

Mains Avg V1, Mains Avg 

V2, Mains Avg V3) 

exceed value given by setpoint 

Mains Avg >V MP 

(

Mains protect 

group), the MCB is opened and message 

Mains Avg x >V 

appears in alarm list and his-

tory record. BO 

Common MP 

is activated (

x indicates number of phase

). 

MP fmns under 

Mains frequency was under the 

Mains <f 

limit for 

Mains f del 

time

. 

Under frequency pro-

tection is based on 

Mains protect

: 

Mains <f 

and 

Mains f del 

setpoints. 

MP fmns over 

Mains frequency was over the 

Mains >f 

limit for 

Mains f del 

time

. 

Over frequency protec-

tion is based on 

Mains protect

: 

Mains >f 

and 

Mains f del 

setpoints. 

Bus meas error 

Bus measurement error is issued if bus voltage is out of limits. For details, see descrip-
tion of the 

Gener protect

: 

BusMeasError 

setpoint in IGS-NT-x.y-Reference Guide. 

OfL StartBlck 

This alarm indicates wrong setpoints setting that disables engine start or load takeover. 
Incorrect combination of 

ProcessControl

: 

Island enable; ParallelEnable; Synchro 

enable; MF start enable 

setpoints setting is the reason why this alarm is issued. 

See 

AUT mode 

section of the 

OFF-MAN-AUT mode 

chapter in IGS-NT-x.y-Reference 

Guide for SPTM, SPI or COMBI application. 

StartBlck 

This alarm indicates wrong setpoints setting that disables start of gensets. Incorrect 
combination of 

ProcessControl

: 

Island enable; ParallelEnable; Synchro enable; MF 

start enable

setpoints setting is the reason why this alarm is issued. 

See 

OFF-MAN-AUT mode 

chapter in IM-NT-MCB-MGCB Reference Guide. 

BOC IDMT 

Indicates current IDMT protection activation. Current IDMT protection is inverse definite 
minimum time protection which is based on the generator current. Protection reaction 
time depends on overcurrent value. High overcurrent means short reaction time whereas 
low overcurrent means longer reaction time. Protection is based on setpoints 

Generator 

protect

: 

2Inom del 

and 

Basic settings

: 

Nomin current. 

MPR Imains IDMT 

Indicates current IDMT protection activation. Current IDMT protection is inverse definite 
minimum time protection which is based on the mains current. Protection reaction time 
depends on overcurrent value. High overcurrent means short reaction time whereas low 
overcurrent means longer reaction time. 
This protection is active if the 

Mns2Inom prot 

setpoint is set to ENABLED. Protection is 

based on setpoints 

Mains protect

: 

Mains2Inom del 

and 

Basic settings

: 

Nomin current. 

BOR IbusL IDMT 

Indicates current IDMT protection activation. Current IDMT protection is inverse definite 
minimum time protection which is based on the left bus current. Protection reaction time 
depends on overcurrent value. High overcurrent means short reaction time whereas low 
overcurrent means longer reaction time. 
This protection is active if the 

BusL2Inom prot 

setpoint is set to ENABLED. Protection is 

based on setpoints 

BusL protect

: 

BusL2Inom del 

and 

Basic settings

: 

Nomin current. 

BOC ShortCurr 

Generator short current protection was activated. Generator current was over 

Generator 

protect

: 

Ishort 

level for 

Ishort del. 

time. 

BOC Overload 

Indicates overload IDMT protection activation. Overload IDMT protection is inverse defi-
nite minimum time protection which is based on the generator power. Protection reaction 
time depends on generator power value. High generator overload means short reaction 
time whereas low generator overload means longer reaction time. Protection is based on 
setpoints 

Generator protect

: 

OverldStrtEval 

and 

2POverldStEvDel. 

Table 8 - Digital Controller List of Alarms

NT

Alarm/History

Record

Description

Discount-Equipment.com

Содержание MGG155




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды