manualshive.com logo in svg

Generac Power Systems MGG155, Руководство по эксплуатации

Поделиться
Скачать
Generac Power Systems MGG155 Скачать руководство пользователя страница 53

Troubleshooting

35319 C

MGG155/210 Operating Manual

49

BOC L1, L2 or L3 over 

Generator L1, L2 or L3 voltage was over the 

Gen >V BOC 

limit for 

Gen V del 

time

. 

Over-

voltage protections are based on 

Gener protect

: 

Gen >V BOC 

and 

Gen V del 

setpoints. 

This alarm is issued if voltage protections are based on phase to neutral voltages. It 
means that 

Basic settings

: 

FixVoltProtSel 

is set to PHASE-NEUTRAL.

Sd L1, L2 or L3 over 

Generator L1, L2 or L3 voltage was over the 

Gen >V SD 

limit for 

Gen V del 

time

. 

Over-

voltage protections are based on 

Gener protect

: 

Gen >V SD 

and 

Gen V del 

setpoints. 

This alarm is issued if voltage protections are based on phase to neutral voltages. It 
means that 

Basic settings

: 

FixVoltProtSel 

is set to PHASE-NEUTRAL. 

BOC L12, L23 or L31 under 

Generator L12, L23 or L31 voltage was under the 

Gen <V BOC 

limit for 

Gen V del 

time

. 

Undervoltage protections are based on 

Gener protect

: 

Gen <V BOC 

and 

Gen V del 

set-

points. This alarm is issued if voltage protections are based on phase to phase voltages. 
It means that 

Basic settings

: 

FixVoltProtSel 

is set to PHASE-PHASE. 

BOC L12, L23 or L31 over 

Generator L12, L23 or L31 voltage was over the 

Gen >V BOC 

limit for 

Gen V del 

time

. 

Overvoltage protections are based on 

Gener protect

: 

Gen >V BOC 

and 

Gen V del 

set-

points. This alarm is issued if voltage protections are based on phase to phase voltages. 
It means that 

Basic settings

: 

FixVoltProtSel 

is set to PHASE-PHASE. 

Sd L12, L23 or L31 over 

Generator L12, L23 or L31 voltage was over the 

Gen >V SD 

limit for 

Gen V del 

time

. 

Overvoltage protections are based on 

Gener protect

: 

Gen >V SD 

and 

Gen V del 

set-

points. This alarm is issued if voltage protections are based on phase to phase voltages. 
It means that 

Basic settings

: 

FixVoltProtSel 

is set to PHASE-PHASE.  

BOC fgen under 

Generator frequency was under the 

Gen <f 

limit for 

Gen f del 

time

. 

Under frequency pro-

tection is based on 

Gener protect

: 

Gen <f 

and 

Gen f del 

setpoints.  

BOC fgen over 

Generator frequency was over the 

Gen >f 

limit for 

Gen f del 

time

. 

Over frequency protec-

tion is based on 

Gener protect

: 

Gen <f 

and 

Gen f del 

setpoints.  

BOC ReversePwr 

This alarm is issued by the reverse power protection. This protection is based on 

Gener 

protect

: 

Reverse power 

and 

ReversePwr del 

setpoints. This alarm means that either 

engine speed/power control does not work properly or generator current transformers 
(CT’s) are connected in a wrong way. 

MP L1, L2 or L3 under 

Mains L1, L2 or L3 voltage was under the 

Mains <V MP 

limit for 

Mains V del 

time

. 

Under-

voltage protections are based on 

Mains protect

: 

Mains <V MP 

and 

Mains V del 

set-

points. This alarm is issued if voltage protections are based on phase to neutral voltages. 
It means that 

Basic settings

: 

FixVoltProtSel 

is set to PHASE-NEUTRAL. 

MP L1, L2 or L3 over 

Mains L1, L2 or L3 voltage was over the 

Mains >V MP 

limit for 

Mains V del 

time

. 

Over-

voltage protections are based on 

Mains protect

: 

Mains >V MP 

and 

Mains V del 

set-

points. This alarm is issued if voltage protections are based on phase to neutral voltages. 
It means that 

Basic settings

: 

FixVoltProtSel 

is set to PHASE-NEUTRAL. 

MP L12, L23 or L31 under 

Mains L12, L23 or L31 voltage was under the 

Mains <V MP 

limit for 

Mains V del 

time

. 

Undervoltage protections are based on 

Mains protect

: 

Mains <V MP 

and 

Mains V del 

setpoints. This alarm is issued if voltage protections are based on phase to phase volt-
ages. It means that 

Basic settings

: 

FixVoltProtSel 

is set to PHASE-PHASE. 

MP L12, L23 or L31 over 

Mains L12, L23 or L31 voltage was over the 

Mains >V MP 

limit for 

Mains V del 

time

. 

Overvoltage protections are based on 

Mains protect

: 

Mains >V MP 

and 

Mains V del 

setpoints. This alarm is issued if voltage protections are based on phase to phase volt-
ages. It means that 

Basic settings

: 

FixVoltProtSel 

is set to PHASE-PHASE. 

Table 8 - Digital Controller List of Alarms

NT

Alarm/History

Record

Description

Discount-Equipment.com

Содержание MGG155




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды