manualshive.com logo in svg

Generac Power Systems MAGNUM MLT6SKDS, Руководство пользователя

Поделиться
Скачать
Generac Power Systems MAGNUM MLT6SKDS Скачать руководство пользователя страница 23

General Information

Owner’s Manual for MLT6SMDS - MLT6SKDS Light Tower

19

Power Zone–DLA (If Equipped)

The  Power  Zone–DLA  is  an AUTO  start  controller  that
monitors  the  unit  and  indicates  operational  status  and
fault  conditions.  The  controller  can  be  programmed  to
automatically start or stop based on time schedule, fault
condition, or load demand. 
The  controller  constantly  monitors  vital  generator  and
engine functions for a number of preprogrammed alarm
and  fault  conditions.  When  a  fault  condition  occurs,  the

engine  shuts  down  automatically  and  the  LCD  window
shows  the  fault  that  caused  the  shutdown.  To  resume
operation, the fault condition must be corrected.
This  controller  records  a  history  of  unit  performance,
which  may  be  viewed  at  any  time  and  will  not  be  lost
when the controller is powered down.

Figure 2-13. Power Zone–DLA Layout

Controller Features and Functions

(A) The Liquid Crystal Display (LCD) Window

Displays the various operating screens. By viewing these
screens,  the  operator  can  monitor  both  the  engine  and
generator status while the unit is running.

(B) Select LED

Illuminates when the unit is running in AUTO mode.

(C) Start LED

Illuminates when the unit is running in MANUAL mode.

(D) Start Button

Starts the engine if there are no shutdown errors and the
engine is in “ready to start” status.

(E) Stop Button

Shuts  down  the  unit  and  puts  the  controller  into  STOP
mode, whether in MANUAL mode or AUTO mode.

NOTE: 

To  prevent  damage  to  the  generator  and  con-

nected  equipment,  remove  all  loads  from  the  generator
by  opening  all  circuit  breakers  (turn  OFF  [O])  before
pressing the STOP button.

(F) Stop LED

Illuminates  when  the  unit  is  in  STOP  mode  and  flashes
when  an  Electrical  Trip  and  Shutdown  Fault  has
occurred.

(G) Select Button

Confirms  entries  chosen  in  the  various  edit  menus  and
screens. Navigates between AUTO and MANUAL mode.

(H) Menu Navigation

Up/down  arrows  (↑,  ↓)  used  to  navigate  through  the
various  operator  screens.  They  are  also  used  to  raise
and  lower  the  mast  on  units  equipped  with  an  electric
winch.

Select

A

B

C

D

F

G

H

E

002353

Содержание MAGNUM MLT6SKDS





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды