manualshive.com logo in svg

Generac Power Systems MAGNUM MLT4250, Руководство пользователя

Поделиться
Скачать
Generac Power Systems MAGNUM MLT4250 Скачать руководство пользователя страница 24

Operation

20

Owner’s Manual for MLT Light Tower

Figure 3-9. Connecting Generator Output Lugs

Voltage Selector Switch

See 

Figure 3-10

. The voltage selector switch

mechanically changes the connections between the
generator output leads and the connection lugs on the
main control panel. Voltage ranges are selected by
rotating the handle on the switch to the desired voltage.

IMPORTANT NOTE: NEVER 

change the voltage selec-

tor switch while the engine is running or the controller is 
on. If the engine is running or starts while the setting is 
changed, severe arcing will occur causing damage to the 
switch and generator windings.

The voltage selector switch is equipped with a lockout
mechanism. Once the proper voltage has been selected,
insert a padlock through the lockout hole(s). By locking
the handle in place, unauthorized changing of the voltage
setting is prevented.

Figure 3-10. Selecting Voltage

Emergency Stop Switch

The unit is equipped with one emergency stop switch.
For location of the emergency stop switch, refer to

Component Locations

. The red switch is clearly labeled

EMERGENCY STOP. The switch can be accessed and
activated with all doors closed and locked.
Activate the emergency stop switch by pushing the red
button in until it locks down. This will trip the main circuit
breaker which will open the contact, disconnecting the
load to the connection lugs. This will also open the fuel
circuit, shutting down the engine.
The switch will remain closed until it is pulled out.

Figure 3-11. Emergency Stop Switch

NOTE: 

Use the emergency stop switch only when the

unit must be shut down immediately. For any other shut
down, refer to 

Shutting Down the Unit

.

004529

B

A

VOLTAGES AT RECEPTACLES

277/480V 3-PHASE

Switch styles vary by model.

L1-L2 = 480V 

L1-N = 277V 

N = 

L2-L3 = 480V 

L2-N = 277V

L3-L1 = 480V 

L3-N = 277V

277/
480V

120/
208V

 RECEPTACLE 

L-L 

L-N

GFCI  

- 

139V

GFCI w/Buck 

- 

120V

Twist-locks 240V 

139V

= Not recommended for normal use

L1-L2 = 208V 

L1-N = 120V 

N = 

L2-L3 = 208V 

L2-N = 120V

L3-L1 = 208V 

L3-N = 120V

VOLTAGES AT RECEPTACLES

120/208V 3-PHASE

Switch styles vary by model.

 RECEPTACLE 

L-L 

L-N

GFCI  

- 

120V

GFCI w/Buck 

- 

120V

Twist-locks 208V 

120V

277/
480V

120/
208V

120/
240V

L1-L2 = 240V 

L1-N = 120V 

N = 

L2-L3 = 240V 

L2-N = 208V

L3-L1 = 240V 

L3-N = 120V

VOLTAGES AT RECEPTACLES

120/240V 3-PHASE

Switch styles vary by model.

 RECEPTACLE 

L-L 

L-N

GFCI  

- 

120V

GFCI w/Buck 

- 

120V

Twist-locks 120V 

0/120V

120/
240V 3PH

277/
480V

120/
208V

120/
240V 
1PH

4 Position Voltage Selector Switch Option

= Not recommended for normal use

002811

L1-L2 =    - 

L1-N = 120V 

N = 

L2-L3 =    - 

L2-N =    -

L3-L1 = 240V 

L3-N = 120V

VOLTAGES AT RECEPTACLES

120/240V 1-PHASE

Switch styles vary by model.

 RECEPTACLE 

L-L 

L-N

GFCI  

- 

120V

GFCI w/Buck 

- 

120V

Twist-locks 240V 

120V

120/
208V

120/
240V

002812

002811

002809

002810

002393

Discount-Equipment.com

Содержание MAGNUM MLT4250


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды