Generac Power Systems MAGNUM MLT4250 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 49

background image

Maintenance

Owner’s Manual for MLT Light Tower

33

Resetting the “Time to Service”

Reminder

The Magnum Digital Controller (MDC) will display
“WrnMaintenance” when the unit is due for maintenance
or service. The maintenance or service interval is set at
250 hours of engine running time. Once the unit has
been serviced, the Time to Service reminder needs to be
reset to the 250 hour interval. The following procedure
demonstrates how to reset the running hours to 250:

1.

With the unit shut down, power up the controller
with the Control Power switch. The Initialization
screen will be displayed. The controller will toggle
automatically to the Ready display screen.

2.

Press the PAGE SELECT button. The next screen
will display lines of text; starting with Password,
which will have a (>) in front of it, then Basic
settings, Engine params, Engine protect, etc.

3.

Press the



button to move the (>) cursor down to

“Engine protect.”

Figure 4-2. Resetting Service Reminders

4.

5.

Press ENTER. “WrnMaintenance” will appear at
the top left of the display screen. The current
service time hour setting (0) will be one line below
it on the right side.

6.

Press ENTER. The current run time in hours will
now appear on the left side of the display screen,
directly under “WrnMaintenance.”

7.

Press



and reset the current run time hour setting

to 250. If you pass the 250 time interval, use



to

get back to the 250 time interval.

Table 4-1. Basic Maintenance Guide (Isuzu)

Item

Daily

250

Hours

500

Hours

1000

Hours

Check Oil Level



Check Coolant Level



Check Fuel Level



Drain Fuel Filter



Check Tire Pressure



Check All Electrical Connections



Clean Battery



Check Fan Belt Tension (Replace If Necessary)



Inspect Radiator Fins For Debris, Clean As Required



Preheating Condition Check



Check Engine Starting Conditions And Noise Conditions



Check Exhaust Smoke Condition



Inspect Light Tower Winch For Proper Operation



Replace Engine Oil



Replace Fuel Filter Element



Clean Water Sedimenter Element



Electromagnetic Pump Filter Replacement or Cleaning



Check Fan Belt Tension (Replace If Necessary)



Oil Filter Element Replacement



Replace Air Filter Element



Lubricate Leveling Jacks



Replace Heated Fuel Filter (If Equipped)



Inspect Engine Starting Battery



004527

Discount-Equipment.com

«
...
34
35
36
37
38
...
»

Содержание MAGNUM MLT4250


















































Отзывы:

Нет отзывов

Похожие инструкции для MAGNUM MLT4250

Бренд: GE Страницы: 138

Бренд: Makita Страницы: 84

BODY ARMOR PRO TERM

Бренд: Darco Страницы: 6

Бренд: Olsen Страницы: 58

Бренд: ParaBody Страницы: 6

Бренд: ParaBody Страницы: 11

Бренд: Rain Harvesting Страницы: 2

Бренд: Zell Страницы: 32

Бренд: Uflex Страницы: 16

Air 2000 Outdoor

Бренд: ubbink Страницы: 21

ULTRATHERM 908i

Бренд: gbo Страницы: 32

Бренд: Dantel Страницы: 6

Бренд: Zero 88 Страницы: 22

Бренд: Yaasa Страницы: 20

i-limb access hand

Бренд: Össur Страницы: 246

PROPRIO FOOT PSX01

Бренд: Össur Страницы: 374

Бренд: Habitat Страницы: 6

Бренд: Godox Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды