manualshive.com logo in svg

Generac Power Systems MAGNUM MLT4250, Руководство пользователя

Поделиться
Скачать
Generac Power Systems MAGNUM MLT4250 Скачать руководство пользователя страница 29

Operation

Owner’s Manual for MLT Light Tower

25

Make sure any problems that caused the main circuit
breaker to trip are corrected before returning the switch
to the ON (I) position.

NOTE: 

The main circuit breaker interrupts power to the

connection lugs only. The receptacle panel has power
even if the main circuit breaker is in the OFF (O) position.
The receptacle panel main circuit breaker

,

 located next to

the main circuit breaker, will disconnect all power to the
receptacle panel.

Remote Start Terminal Block

The remote start terminal block provides a connection for
installation of a remote start switch which will allow the
unit to be started by a remote dry-contact closure switch.
To locate the remote start terminal block, see 

Main

Control Panel

. 

Figure 3-20. Remote Start Switch Terminals

1. Before entering Auto mode, verify that the contacts

on any remote switch linked to the unit are 

OPEN

.

If the contacts on a remote switch are closed, the
engine will crank and start when Auto mode is
entered. 

2. See 

Figure 3-20

. Attach the switch leads to the

two unused terminals on the unit’s remote start
terminal block (A). For additional information, refer
to 

Starting the Unit—Auto/Remote

.

Transfer Switch

When the unit is used as a standby power supply, it must
be equipped with a transfer switch which isolates it from
the utility’s distribution system. A transfer switch is
designed to transfer electrical loads from the normal
power source (utility) to the emergency power source
(generator) when normal voltage falls below a prescribed
level. The transfer switch automatically returns the load
back to the normal source when power is restored back
to operating levels.

Figure 3-21. Transfer Switch Operation

Installation of a transfer switch or other type of remote
starting device is the responsibility of the user. Installation
of such devices must be performed by following all
directions supplied by the manufacturer of the switch. If
attaching the unit to a power supply normally serviced by
a utility company, notify the utility company and check
local and state regulations. Familiarize yourself with all
instructions and warning labels supplied with the switch.

A

002806

(000226a)

Phase rotation must be compatible. 
Incompatible phase rotation could result 
in equipment damage, death or serious injury.

 

WARNING

A

Incoming Utility Power

B

Emergency Distribution Panel (Generator 
Power)

C

Main Distribution Panel (Utility Power)

D

Transfer Switch

E

Power From Generator

F

Utility Meter

WHITE

Incoming Utility Power

GRAY

Normal Utility Power Circuit

BLACK

Emergency Generator Power Circuit

C

D

E

F

002807

A

B

(000150)

DANGER

Electrocution. Never connect this unit to the electrical
system of any building unless a licensed electrician 
has installed an approved transfer switch. Failure to 
do so will result in death or serious injury.

(000155)

WARNING

Only a trained and licensed electrician should perform
wiring and connections to unit. Failure to follow proper
installation requirements could result in death, serious
injury, and damage to equipment or property.

Discount-Equipment.com

Содержание MAGNUM MLT4250


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды