Generac Power Systems GTH1000 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 74

Generac Power Systems GTH1000 Скачать руководство пользователя страница 18

3-2

SECTION 3: CARBURETION AND FUEL SYSTEM

CHOKE
LINK

Figure 3-5.

6. Remove choke link (Figure 3-5), throttle link (Figure 3-4) and fuel

shut-off solenoid wire from carburetor.

7. Slide carburetor off mounting studs.

CARBURETOR CLEANING

For cleaning purposes, the carburetor's float bowl may be removed.
It is recommended that all jetting be left in place while cleaning the
carburetor. Be sure to use a cleaner that won't damage rubber, neo-
prene, or plastic parts.

Note: The left and right main jets are different sizes.

If the fuel-shutoff solenoid is suspected of being faulty, it is replaceable
by simply unthreading it from the float bowl, and installing a new one
in its place. It can be checked by applying 12 volts to it. If you hear it
click, it is most likely working properly. If there is anything else wrong
with the carburetor, it is recommended that the entire carburetor be
replaced with a new one.

Note: Be careful not to lose the spring that is located inside

the fuel shutoff solenoid when removing the plunger.

CARBURETOR INSTALLATION - VERTICAL SHAFT

1. Slide new carburetor gasket and carburetor onto the studs.

2. Slide new plenum gasket and plenum onto the studs.

3. Install the four nuts and torque to 5.4 Nm (48 in. lbs.).

4. Connect the fuel line and clamp.

5. Reassemble the throttle link to the balljoint on the carburetor.

6. Connect the breather tube and EVAP hose if equipped.

7. Connect the fuel-shutoff solenoid.

PLENUM

MANIFOLD

PLENUM

GASKET

CARBURETOR

GASKET

Figure 3-6.

8. Reinstall choke link on carburetor and clip the link into the

bellcrank.

9. Perform a static governor adjustment.

(See “Static Governor

Adjustment”, page 4-2)

10. Start engine and allow to warm up for 5 minutes.

11. Move speed control lever to slow speed position and hold throttle

lever against idle stop screw.

12. Adjust the idle top screw to maintain ~1800 RPM idle.

13. Slowly move speed control lever to high speed position.

Figure 3-7.

Note: The high speed screw may need adjusting to reach the speed

control stop without exceeding 3800 RPM.

14. With the speed control in the high speed position, adjust the high

speed screw to obtain the desired engine speed. Do not exceed
3800 RPM.

«
...
16
17
18
19
20
...
»

Содержание GTH1000











































































Отзывы:

Нет отзывов