Generac Power Systems GTH1000 Скачать руководство пользователя страница 66

Страница: 66 / 74

13-4

SECTION 13: ENGINE ASSEMBLY

Figure 13-12. Torque Flywheel Nut

ADJUST IGNITION COIL AIR GAP

1. Rotate flywheel until magnet is under coil laminations.

2. Place 0.20-.30mm (.008"-.012") thickness, non-magnetic gauge

between magnet and coil laminations, Figure 13-13.

Figure 13-13. Adjust Coil Air Gap

3. Loosen mounting screw so magnet will pull coil down against

thickness gauge.

a. Torque screws to 4.75 Nm (40 in. lbs.).

4. Rotate flywheel to remove thickness gauge.

5. Repeat Steps 1 through 4 for second coil.

INSTALL CYLINDER HEADS

1. Install cylinder head with new gasket.

2. Lubricate threads of head bolts with one drop of oil.

a. Torque head bolts in sequence shown (Figure 13-14) to 29.9 Nm

(22 ft. lbs.).

3. Insert push rods into recess in tappets.

A-B-C-D-E-F

CYLINDER HEAD TORQUE SEQUENCE:













Figure 13-14. Cylinder Head Torque

INSTALL ROCKER ARMS

1. Lubricate rocker arms and ball studs with clean engine oil.

2. Assemble ball studs, rocker arms, jam nuts and guide plates (with

tabs facing up) to cylinder head, Figure 13-15.

a. Make sure that the push rods are in the proper location on the

tappets and the rocker arms.

STUD

ROCKER ARM

NUT

GUIDE PLATE
(WITH TABS FACING UP)

Figure 13-15. Install Rocker Arms

Содержание GTH1000











































































Результаты поиска

Содержание GTH1000

Отзывы:

Похожие инструкции для GTH1000

Бренды по названию

Популярные бренды

Generac Power Systems GTH1000, Руководство по обслуживанию

Результаты поиска

Содержание GTH1000

Отзывы:

Похожие инструкции для GTH1000

Бренды по названию

Популярные бренды