Generac Power Systems GTH1000 Скачать руководство пользователя страница 26

Страница: 26 / 74

Figure 3-28. Install Secondary Diaphragm

Figure 3-29. Install Secondary Cover

18. Draw a bubble of leak detector over the “OUTLET” port. The

bubble should hold for several seconds with the regulator inlet
pressurized. Return to step 10 if the bubble doesn’t hold for several
seconds. See Figure 3-30.

19. Remove air pressure supply and primary pressure test gauge.

Replace the 1/8” pipe plug in the primary pressure test opening.
See Figure 3-31.

20. Install the regulator.

a. Clean all threaded areas and use a commercially available pipe

sealant. Make sure sealant does not get inside of the regulator.

b. Connect LP line(s), reconnect battery and turn on fuel supply at

the tank(s).

c. Turn ignition switch to the "ON" position to verify that the solenoid

is opening.

d. Check all fuel connections with a leak detector. If leaks are pres-

ent, go back to Step 20a.

e. Run the engine until it is at full operating temperature.

21. Repair is now complete.

Figure 3-30. Check Outlet Port

Figure 3-31. Re-install Pipe Plug in Test Opening

3-10

SECTION 3: CARBURETION AND FUEL SYSTEM

Содержание GTH1000











































































Результаты поиска

Содержание GTH1000

Отзывы:

Похожие инструкции для GTH1000

Бренды по названию

Популярные бренды

Generac Power Systems GTH1000, Руководство по обслуживанию

Результаты поиска

Содержание GTH1000

Отзывы:

Похожие инструкции для GTH1000

Бренды по названию

Популярные бренды