Generac Power Systems GTH1000 Скачать руководство пользователя страница 60

Страница: 60 / 74

12-2

SECTION 12: PISTON, RINGS & CONNECTING ROD INSPECTION & ASSEMBLY

Figure 12-4. Checking Ring End Gap

Figure 12-5. Check Piston Pin Bore

CHECKING PISTON PIN AND CONNECTING ROD

1. Check piston pin, Figure 12-6.

a. Replace if less than 19.97mm (.7862") or if it is .01mm (.0005")

out of round.

2. Check connecting rod bearings (see Figure 12-7).

Note: If piston pin or crankpin bearing ends are scored or worn the
connecting rod must be replaced.

Figure 12-6. Check Piston Pin

CRANKPIN BEARING

PISTON PIN BEARING

Figure 12-7. Check Rod Bearings

ASSEMBLE PISTON AND CONNECTING ROD

Lubricate parts with engine oil and assemble #1 piston and connect-
ing rod, Figure 12-8.

1. Notch or casting mark on the piston top must face towards the

flywheel.

2. Number "1" on connecting rod must face PTO side (opposite notch

or casting mark on piston).

a. Install piston pin locks with needle nose pliers.

Lubricate parts with engine oil and assemble #2 piston and connect-
ing rod, Figure 12-9.

1. Notch or casting mark on the piston top must face towards the

flywheel.

2. Number "2" on connecting rod must face PTO side (away from the

flywheel).

a. Install piston pin locks with needle nose pliers.

Содержание GTH1000











































































Результаты поиска

Содержание GTH1000

Отзывы:

Похожие инструкции для GTH1000

Бренды по названию

Популярные бренды

Generac Power Systems GTH1000, Руководство по обслуживанию

Результаты поиска

Содержание GTH1000

Отзывы:

Похожие инструкции для GTH1000

Бренды по названию

Популярные бренды