Generac Power Systems G0072190 Скачать руководство пользователя страница 5

Safety Rules & General Information

Owner’s Manual for Australian 3-Phase 50 Hz Air-Cooled Generator Sets

1

Section 1: Safety Rules & General Information

Introduction

Thank you for purchasing this compact, high perfor-
mance, air-cooled, engine-driven generator set. It is
designed to automatically supply electrical power to oper-
ate critical loads during a utility power failure.
This unit is factory installed in an all-weather, metal
enclosure that is intended exclusively for outdoor installa-
tion. This generator set will operate using either vapor
withdrawn liquid propane (liquid propane gas [LPG]) or
natural gas (NG).

NOTE: 

This generator set is suitable for supplying typical

residential loads such as induction motors (sump pumps,
refrigerators, air conditioners, furnaces, etc.), electronic
components (computer, monitor, TV, etc.), lighting loads,
and microwaves, when sized correctly. This unit is
equipped with a Wi-Fi

®

 module, which allows the genera-

tor set owner to monitor generator set status from any-
where they have Internet access. 

NOTE: 

Wi-Fi

®

 is a registered trademark of Wi-Fi Alli-

ance

®

.

The information in this manual is accurate based on
products produced at the time of publication. The manu-
facturer reserves the right to make technical updates,
corrections, and product revisions at any time without
notice.

Read This Manual Thoroughly

If any portion of this manual is not understood, contact
the nearest Independent Authorized Service Dealer
(IASD) for starting, operating, and servicing procedures.
The owner is responsible for correct maintenance and
safe use of the unit.
This manual must be used in conjunction with all other
supporting product documentation supplied with the
product.
SAVE THESE INSTRUCTIONS for future reference. This
manual contains important instructions that must be fol-
lowed during placement, operation, and maintenance of
the unit and its components. Always supply this manual
to any individual that will use this unit, and instruct them
on how to correctly start, operate, and stop the unit in
case of emergency.

Safety Rules

The manufacturer cannot anticipate every possible cir-
cumstance that might involve a hazard. The alerts in this
manual, and on tags and decals affixed to the unit, are
not all inclusive. If using a procedure, work method, or
operating technique that the manufacturer does not spe-
cifically recommend, verify that it is safe for others and
does not render the equipment unsafe.
Throughout this publication, and on tags and decals
affixed to the unit, DANGER, WARNING, CAUTION, and
NOTE blocks are used to alert personnel to special
instructions about a particular operation that may be haz-
ardous if performed incorrectly or carelessly. Observe
them carefully. Alert definitions are as follows:

NOTE: 

Notes contain additional information important to

a procedure and will be found within the regular text of
this manual.

These safety alerts cannot eliminate the hazards that
they indicate. Common sense and strict compliance with
the special instructions while performing the action or
service are essential to preventing accidents.

(000100a)

Consult Manual. Read and understand manual
completely before using product. Failure to 
completely understand manual and product 
could result in death or serious injury.

WARNING

(000001)

DANGER

Indicates a hazardous situation which, if not avoided, 
will result in death or serious injury.

(000002)

WARNING

Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.

(000003)

CAUTION

Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.

Содержание G0072190









































Отзывы: