4
1.1 UNPACKING
• Remove all packaging material.
• Remove separate accessory box.
• Remove the generator from carton.
1.1.1 ACCESSORY BOX
Check all contents. If any parts are missing or damaged, locate an
authorized dealer at 1-888-436-3722.
• 1 - Owner’s manual
• 1 - Bottle of Oil SAE 30 with funnel
• 3 - Product Registration Cards (English, Spanish, French)
• 2 - 8” WHEELS
• 1 - Axle
• 1 - Frame Foot
• 1 - Handle with grip
• 1 - Hardware Bag
– 1 - Plastic Spacer
– 2 - M8-1.25 x 40 Bolts
– 1 - Handle Bracket
– 1 - M6-1.0 x 40 Bolt
– 2 - Rubber Bumpers
– 2 - M8-1.25 x 16 Bolts
– 2 - Cotter Pins
– 1 - M6-1.0 Hex Flange Nut
– 2 - M8-1.25 Hex Flange Nuts
1.2 ASSEMBLY
The generator requires some assembly prior to using it. If
problems arise when assembling the generator, please call the
Generator Helpline at 1-888-436-3722.
The following tools are required to properly assemble the
generator:
• Needle-nose pliers
• Ratchet and 12mm (1/2") socket
• 12mm (1/2") box wrench or adjustable wrench
1.2.1 ASSEMBLING THE ACCESSORY KIT
The wheels are designed for the unit to greatly improve the
portability of the generator.
NOTICE:
The wheels are not intended for over-the-road-use.
1. Refer to Figure 1 to install the wheels as shown.
– Slide the axle through the frame brackets.
– Slide on the wheels then install the cotter pins.
2. Refer to Figure 1 to install the wheel bumpers as shown.
– Secure the two rubber bumpers to the frame foot using
two M8-1.25 Hex Flange Nuts (if not already assembled).
– Place the frame foot under the frame and secure with two
M8-1.25 x 16 bolts.
3. Refer to Figure 2 to install the handle assembly as shown.
– Install the handle bracket to the frame using two M8-1.25
x 40 bolts (if not already assembled).
– Slide the plastic spacer onto the handle assembly then
align with the holes in the handle bracket (if not already
assembled).
– Secure the handle assembly to the handle bracket using
the M6-1.0 x 40 bolt and one M6-1.0 hex flange nut.
Figure 1 – Wheel Assembly
Figure 2 – Handle Kit
M8-1.25 x 40
BOLTS
1 X M6-10 HEX FLANGE NUT
1x HANDLE W/GRIP
1x PLASTIC SPACER
1x M6-1.0X40 BOLT
1x HANDLE BRACKET
1.3 EMISSION INFORMATION
The Environmental Protection Agency requires that this generator
comply with exhaust emission standards. The generator is
certified to meet the applicable EPA emission levels. It is important
that you follow the maintenance specifications provided in this
manual to ensure that your engine complies with the applicable
emission standards for the duration of the engine's life. This engine
is certified to operate on gasoline. The emission control system on
your generator consists of the following:
• Fuel Metering System
• Ignition System
– Carburetor
–
Spark Plug
– Fuel Lines
–
Ignition Coil
• Air Induction System
– Intake Pipe/Manifold
– Air Cleaner
The Emissions Compliance Period referred to on the Emissions
Compliance label indicates the number of operating hours for
which the engine has been shown to meet Federal Emissions
requirements.
General Information
Содержание CENTURION 006104-1
Страница 52: ...50 Remarques ...
Страница 53: ...51 51 Remarques ...
