manualshive.com logo in svg

Generac Power Systems 6.75, Руководство оператора

Поделиться
Скачать
Generac Power Systems 6.75 Скачать руководство пользователя страница 23

CONTACT US AT 

1-888-545-6576

         23

 

Note:

 Ensure that the Drive Cable does not kink or get over stressed during the 

following procedure. 

The Belt Guide will interfere with the Transmission Housing and Belt when 
the Transmission is rotated.  The Belt can be repositioned and the Belt Guide 
can be moved out of the way slightly as needed. 

11.

 

Continue to rotate the Transmission to gain access to the Belt retainers and 
Screws on the bottom of the Transmission (

Figure 38

). 

12.

 

Remove the two Retainer Screws where the Belt wraps around the Pulley and 
loosen the other two using a Philips Head Screwdriver. 

13.

 

Rotate the Belt retainers away from the Transmission Pulley and remove the 
Belt. 

14.

 

Install a new Drive Belt around the Transmission Pulley. 

15.

 

Rotate the Transmission Belt Retainers into position and secure with the two 
Screws you removed and tighten the other two using a Philips Head 
Screwdriver. 

16.

 

Rotate the Transmission and Belt up into the Trimmer and position the 
Drive Belt around the Engine Pulley. 

17.

 

Tighten the Belt Guide Locknut (

Figure 37

). 

18.

 

Rotate the rear Drive Belt Guide into position centered behind the Engine 
Pulley and tighten the Locknut with a 7/16" Wrench. 

19.

 

Reconnect the Z-bend end of the Drive Cable into the Bracket hole (

Figure 

36

). 

20.

 

Reattach the Cable Bracket to the Handlebar using two 7/16

˝

 Wrenches 

(

Figure 35

). 

21.

 

Install the Drive Cable Eyelet to the Bail Bar using a 7/16

˝

 Wrench. 

22.

 

Install the Transmission Cover and secure with the four Bolts and Flat 
Washers using a 3/8" Wrench (

Figure 34

). 

23.

 

Position the Trimmer Guard and secure with the four Bolts and Flat Washers 
using the 3/8" Wrench (

Figure 33

). 

24.

 

Install the Trimmer Cord and tip the Trimmer down on the Head Assembly. 

25.

 

After installing the new Belt, be sure to adjust the Cable tension properly by 
adjusting the Jam Nuts (refer to page 25).  Proper tension will extend the life 
of the Belt. 

Replacing the Wheels 

Tool needed: 

 

5/8" Wrench (non Self Propelled model) 

 

9/16" Wrench (Self Propelled model) 

1.

 

Block and stabilize the machine so that the Wheels are off the ground. 

2.

 

Loosen and remove the Locknut with the required Wrench (

Figure 39

). 

Note:

 The self propelled Wheel has a Flat Washer under the Locknut. 

3.

 

Slide the Wheel off the Axle. 

4.

 

Reverse the steps to install the new Wheel. 

Engine Pulley 

Figure 38 

Drive Belt 

Remove 

Belt 
Retainers 

Loosen 

Remove 

Loosen 

Trimmer 
Belt 

Transmission Pulley 

Locknut 

Figure 39 

Wheel 

Содержание 6.75









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды