manualshive.com logo in svg

Generac Power Systems 6.75, Руководство оператора

Поделиться
Скачать
Generac Power Systems 6.75 Скачать руководство пользователя страница 17

CONTACT US AT 

1-888-545-6576

         17

 

Chapter 4: Maintaining The TRIMMER/MOWER 

Regular maintenance is the way to ensure the best performance and long life of your machine.  Please refer to this manual and the 
engine manufacturer's owner's manual for maintenance procedures.  Service intervals listed in the checklist below supersede 
those listed in the engine manufacturer's owner's manual. 

Regular Maintenance Checklist 

Note:

  Consider that the service intervals shown are the maximum under normal operating conditions.  Increase frequencies under 

extremely dirty or dusty conditions. 

P

ROCEDURE

 

B

EFORE 

E

ACH 

U

SE

 

E

VERY 

25

 

H

OURS

 

E

VERY 

50

 

H

OURS

 

E

VERY 

100

 

H

OURS

 

Check Engine Oil Level and add as needed. 

 

 

 

 

Clean Engine Exterior, Cooling Fins and remove collected grass trimmings.* 

 

 

 

 

Check General Equipment Condition, e.g. Nuts, Bolts, Welds, etc. 

 

 

 

 

Replace broken or frayed Cutting Cords. 

 

 

 

 

Check the Mow-Ball

®

 Line Plates for excessive wear. 

 

 

 

 

Check the Trimmer Belt for stretching.  Adjust the Drive Cable if necessary per 
“Adjusting the Trimmer Belt Tension through the Trimmer Control Cable” in 
this Chapter. 

1

st

 time 2 

hours 

 

 

 

Lubricate Throttle Cable, Self Propel Cable and Trimmer Control Cable with 
SAE 30 Oil. 

 

 

 

 

Change the Engine Oil (excluding 6.75 EXi and 7.25 EXi models) 

1

st

 time 5 

 

 

 

Replace the Engine Air Filter Cartridge and foam Pre Filter if equipped. 

 

 

 

 

Remove the Trimmer Guard and clean out any collected debris 

 

 

 

 

Check the Battery Voltage (Electric-Starting models) 

 

 

 

 

Lubricate Chains (Self Propelled models) 

 

 

 

 

Replace the Trimmer Belt 

 

 

 

 

Replace the Self Propel Belt (Self Propelled models) 

 

 

 

 

Replace the Spark Plug. 

 

 

 

 

* Cleaning the top of the Engine during use is critical for proper air flow.  Keeping the Engine clear of debris is necessary for optimum performance. 

Replacing the Mow-Ball

®

 or Line Plates 

Tools and Supplies Needed: 

 

Phillips head Screwdriver with at least a 6" shank 

 

Gloves 

Disassembly 

1.

 

Align the hole in the Anti Wrap Canister with the hole in the internal housing 
at the location shown (

Figure 23

). 

2.

 

Insert a Philips Head Screwdriver into the hole in the Anti Wrap Canister and 
the hole in the internal Housing. 

3.

 

Rotate the Mow-Ball

®

 Assembly until the Screw Driver slides into a hole in 

the shaft, locking it into place. 

Figure 23 

Loosen 

Screw Driver 

Anti Wrap 
Canister 

Mow-Ball

®

 

Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool.  
Disconnect the spark plug wire, keeping it away from the spark plug. 

Содержание 6.75









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды