manualshive.com logo in svg

Generac Power Systems 6.75, Руководство оператора

Поделиться
Скачать
Generac Power Systems 6.75 Скачать руководство пользователя страница 18

18

 

        

GENERAC

®

 

TRIMMER/MOWER

 

Always make sure you remove the screwdriver from the head assembly when 
finished.  Failure to remove the screwdriver could cause injury when the head 
assembly is engaged. 

4.

 

Looking down at the top of the Frame, turn the Mow-Ball

®

 clockwise until it unscrews completely from the Bearing Housing. 

Note:

  

If the Mow-Ball

®

 continues to turn, but does not come off, check to be sure that you locked the Screwdriver into the shaft. 

If the Mow-Ball will not turn by hand a 9/16" Socket can be used on the Bolt (inside the bottom of the Mow-Ball) to loosen it.  

You may need to clean grass or debris out of the recess first. 

5.

 

Slide the Line Plates, Anti Wrap Canister and Spacer off the Shaft (

Figure 24

). 

Assembly 

1.

 

Place the Spacer and Anti Wrap Canister (with the lip facing up) onto the 
Shaft (

Figure 24

). 

2.

 

Ensure the Line Plates are facing top side up as shown.  Align the flats at the 
center of the Line Plates with the flat on the shaft as you slide them onto the 
Shaft.  Ensure the Tabs on the underside of the Line Plates are fully into the 
holes on the tops of the Line Plates so they will fit together tightly. 

3.

 

Place the head of the Mow-Ball

®

 Bolt so it is sitting in the hex cavity at the 

bottom of the Mow-Ball

®

. 

4.

 

Looking down at the top of the Frame, hold the Bolt Head in place with your 
finger and turn the Mow-Ball

®

 counterclockwise to start the Bolt into the 

Shaft. 

5.

 

Tighten the assembly securely by turning the Mow-Ball

®

 counterclockwise 

when looking down on the top of the Frame. 

6.

 

Remove the Screwdriver. 

Note: 

 

When finished there should be no gaps between any of the components. 

Figure 24  

Spacer 

Line Plates 

Anti Wrap 
Canister 

Mow-Ball

®

 

Mow-Ball

®

 

Bolt 

Tab Holes 

Flats in Line 
Plates to Match 
with Shaft 

Improper installation can cause damage to the trimmer bearings.  Follow 
these directions carefully to protect your machine from damage.  Reassemble 
the components in the order shown in

 figure 24

. 

Содержание 6.75









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды