CONTROLS:
(CONTINUED)
FADER REPLACEMENT:
SPECIFICATIONS:
18
20
21
1. UNSCREW THE FADER (B) SCREWS. DO NOT TOUCH INSIDE
SCREWS (C) CAREFULLY REMOVE OLD CROSS FADER AND UNPLUG
CABLE (D)
2. PLUG IN THE NEW CROSS
FADER INTO CABLE (D) AND
PLACE BACK INTO MIXER.
3. SCREW THE CROSS FADER TO
MIXER WITH THE FADER PLATE
SCREWS (B)
4. REPLACE THE FACE OF THE
MIXER AND SCREW THE FOUR
SCREWS BACK IN AND REPLACE THE FADER KNOBS.
INPUTS:
Phono............................................................................3mV,47 K Ohm
Line.........................................................................150 mV, 27 K Ohm
MIC.............................................................1.5 mV, 1 KOhm Balanced
OUTPUTS:
Max..........................................................................20V Peak-to Peak
Rec............................................................................225 mV, 5 K Ohm
GENERAL:
Frequency Response.........................................20Hz - 20KHz +/- 2dB
Distortion..................................................................................< 0.02%
S/N Ratio...................................................................Better than 85 dB
Headphone impedance............................................................32 Ohm
Power Source ..............................................................AC 15V 500mA
Unit dimensions............................................................10” x 3.3” x 12”
.............................................................................(318 x 85 x 356 mm)
Weight.......................................................................10.5 lbs (4.76 kg)
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION
FOR IMPROVEMENT
CHANNEL ROTARY GAIN
The
CHANNEL ROTARY GAIN
allows you to boost the signal of each
individual channel depending on how low or high its input level is
3 BAND EQUALIZER
The
3 BAND EQUALIZER
adjust the tone of each
CHANNE
L by giv-
ing you a choice
3
frequencies (
BANDS
) to adjust , from
LOW,
MIDRANGE (MID)
and
HIGH’s
,you can use the adjustment knobs to
higher or lower the 3 separate frequencies till the sound of the music
program is appropriate for your listening environment.
CHANNEL VOLUME FADER
After you have chosen which input you will use with the
INPUT
SELECTOR
the corresponding
CHANNEL FADER
will allow you to
adjust the volume for that particular
CHANNEL
.
CROSSFADER ASSIGNMENT/ADJUSTMENT SWITCHES
The fader assignment push button allows you to assign which two
channel faders will be controlled by the
CROSSFADER
in the UP po-
sition the
CROSSFADER
will fade between channels (1) and (2), in
the down or pushed in position the
CROSSFADER
will fade between
channels (
3
) and (
4
). The
CURVE ADJUSTMENT
selector lets you
choose between two fader
CURVE
settings, positioning the switch to
the right will give you a gradual
CROSSFADE
and positioning the
switch to the left will give you a quick
CROSSFADE
.
CROSS FADER
The
CROSS FADER
allows you to mix evenly from one source to an-
other. On the
PS-828X
The
CROSSFADER
is assignable between
either channels (1) and (2) or channels (3) and (4) depending on the
position of the fader assignment push button (see above).
The
CROSS FADER
on the
PS-828X
is also removable and if the
need arises can be replaced.The RG-45 (RAILGLIDE™)
DUAL-RAIL CROSS FADER
, which has internal dual stainless steel
rails that allow the slider to ride smoothly and accurately from end to
end can be purchased from your local
GEMINI
dealer.
NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE THE
FADER BACK AND FORTH. PRESSING DOWN ON THE
CONTROLS CAN BEND CONTACTS AND CAUSE A LOSS OF SOUND.
CHANNEL AND MASTER VU METERS
The
PS-828X
has a
VU METER
on each channel that allows you to
monitor the decibel levels of its input, you also have a master output
VU METER
that lets you monitor the decibel levels of the
LEFT
and
RIGHT MASTER
output.
CUE MASTER SWITCH
The
VU METER
has two display modes, in
CUE
mode it will display
the level of the channel you are cueing, in
MASTER
mode it displays
the main
MASTER
output.
MASTER VOLUME ROTARY
The
MASTER VOLUME ROTARY
knob adjust the volume of the
MAIN
output.
CUE/PGM ROTARY
The
CUE/PGM ROTARY
determines the mix between the chosen
CHANNEL CUE SELECTOR
and the
MAIN OUTPUT
mix.
CUE VOLUME ROTARY KNOB
The CUE VOLUME ROTARY KNOB adjusts your HEADPHONE
MONITOR OUTPUT’S volume.
CHANNEL CUE SELECTOR SWITCH
The
CHANNEL CUE SELECTOR SWITCH
allows you to choose
which channel you wish to monitor in your headphones by pressing
this switch on any channel you will be able to listen to that channels
input in your headphones multiple
CHANNEL SWITCHES
can be
pressed to monitor more than on input at a a time.
5
13
14
15
16
17
19
22
19
23
PS-828X
