Gemini GEM-P816 Скачать руководство пользователя страница 30

Страница: 30 / 60

GEM-P816 Installation Instructions

NAPCO Security Systems

WI994C 3/04

Page 28

Alarm Outputs

In UL installations, (1) see Time Selection for timeout requirements; (2) Fire zones must be programmed for PulseAlarm Output, and
the option "Change Pulse Alarm to Cadenced Alarm" must be programmed.

NOTE:

For PGM1 and PGM2 are Lug Active-Low

Outputs.

Alarm; Alarm Restore Telco 1/Telco 3

See Report Telco 1/Telco 3

Alarm; Alarm Restore Telco 2

See Backup Report on Telco 2

Alarm Supervisory

An Alarm Supervisory indicates that there is an open in the circuit to the Alarm (Bell) Output and requires immediate attention. A 2.2K
EOL resistor is required. See wiring diagram.

Ambush (Keypad Ambush); Ambush Codes; Enable Global Ambush

There are two types of Ambush Codes:

(1)

A 2-digit code (prefix) that is entered immediately prior to (and as part of) the regular User

Code and

(2)

A separate and unique User Code. Disarming with an Ambush Code will cause a silent report to be sent to a central

station. Thus, should a user be forced to disarm, he can silently signal an emergency while appearing to be merely disarming the

system. The Ambush Zone will automatically report when programmed to report an alarm.

Ambush Type 1:

(a 2-digit prefix code), this type must not be used in a SIA CP-01 compliant system. Enable as follows: (a) select

“Ambush to Report Event Telco 1/Telco 3” (Address 0475, 0477, 0483, 0485); (b) select “Enable Global Ambush Code” (Address
0720); enter “Global Ambush Code” (Address 1054); and (c) enter an “Ambush CS Report Code” (0340). Each keypad is enabled for
“Ambush” individually (Address 0730-0736).

Ambush Type 2:

(a separate and unique user code), this type must be used in a SIA CP-01 compliant system. Enable as follows: In

the Easy Menu Driven Program Mode (see WI995 or WI1182), the menu selection "

Enter User Code

" is used to program a user code

with a "blank(•) 5" in the area for which the Ambush Code will be used.  Enable all other locations and program as follows: (a) select
“Ambush to Report Event Telco 1/Telco 3” (Address 0475, 0477, 0483, 0485); (b) enter an “Ambush CS Report Code” (0340). Each
keypad is enabled for “Ambush” individually (Address 0730-0736).

Be sure to inform the user what their Ambush Code is, and that the Arm/Disarm Code must be entered less than 10 seconds after the
Ambush Code for an ambush report to be sent.  When “ENABLE GLOBAL AMBUSH” is selected and no Ambush code has been
entered and the keypads have been selected for AMBUSH, then the AMBUSH CODE will default to “99”.

Answering Machine Pickup Without Line Seizure

See Callback-Method Download.

Anti-Jam Communicator Time

If the communicator does not detect a dial tone within 12 seconds, the Anti-Jam feature will be activated. That is, the communicator will
go off line for a 16-second anti-jam interval in order to free the telephone circuit from an incoming call, then make another 12-second
attempt at dial-tone detection. If still unsuccessful, the communicator will again go off line for 16 seconds, then proceed to dial anyway.

Areas; Zone Area 1; Priority Area Arming

The default program will automatically set up Zones 1 through 8 for Zone Area 1. Every zone must be assigned to at least one area
(Address 0526, 0527, 0581, 0582, 0636, 0637, 0691, 0692) to be used. At least one zone must be assigned to Area 1.

Keypad Area Assignments

Silencing Alarm Area (determines which alarms an area may silence);
Subscriber Opening/Closing ID Numbers and Event ID Numbers (if reporting);
System Trouble Subscriber ID Number
If “Priority Area Arming” (Address 0743 & 0744) is selected, the Priority Area must be armed before the Arming Area can be armed.

Auto-Arm if not closed at end of Window; Closing Window; Fail to Close (Not for UL Installations)

AUTO-ARM can be programmed to arm at a specific closing Time (such as: 17:00 representing 5:00 pm), for a notification length of
time (such as: 00:02 representing 2 minutes), and a FAIL-TO-CLOSE has been enabled for a specific day of the week and area, and
Auto Arm if not closed at end of window.  When the start time is reached, the display will notify the occupants that an Auto-Arm will be
initiated in the notification period length of time.  After that period has expired, a 15 minute period will count down to Auto-Arm with the
sounder pulsing.  Auto-Arming may be canceled by arming and disarming the panel. An auto-Arm will be reported as User 33. Auto
Arming can be delayed from 1 to 4 hours by pressing the

button during the 15 minute Auto Arm Period until “

TO DELAY AUTO

ARM

” is displayed and press the number of hours to delay followed by the

button.

Glossar

OUTPUT

WIRING

REMARKS

Alarm Output (Burg.) 3(+) & 4(–)

Single Bell Output; program Alarm Output for Burg (Addr. 0460, 0471, 0479, 0500, 0555, 0610, 0665, 0745)

Pulse Alarm Output