9.0 - SETTING OF PARAMETERS
PAGE 10 - INSTALLER MANUAL
INSTALLER MANUAL - PAGE 11
9.1 - FRONT UNIT (MAIN UNIT)
9.1 - REAR UNIT
Nr.
Nr.
01
02
03
04
05
06
07
08
09
11
12
13
15
16
17
10
17
PARAMETERS
PARAMETERS
Volume of buzzer
Detection range of front central sensors
Detection range of front corner sensors
Detection range of rear central sensors
Detection range of rear corner sensors
STOP zone of front central sensors
STOP zone of front corner sensors
STOP zone of rear central sensors
STOP zone of rear corner sensors
Number of speed signal pulses
Delay of front sensors deactivation
Delay of rear sensors activation
Service display front unit (main unit), system
testing
Front sensors detection
Sensitivity of front sensors to detect
obstacles
Suppression of spare wheel indication
Sensitivity of rear sensors to detect
obstacles
RANGE
RANGE
0, 1, 2 (
)
From 50 to 95 cm
From 50 to 95 cm
From 120 to 180 cm (
)
From 50 to 95 cm
From 35 to 50 cm
From 35 to 50 cm
From 35 to 70 cm
From 35 to 70 cm
Da 1 to 99
0 or from 10 to 60 sec. (
)
0, 1 (
)
0, 1, 2, 3 (
)
0,1 (
)
1, 2, 3 (
)
Ref.1
Ref.2
Ref.3
Ref.4
Ref.5
Ref.6
Ref.7
0, 1, 2, 3 (
)
1, 2, 3 (
)
Ref.1
Ref.2
SETTING
SETTING
2
80
55
160
55
35
35
35
35
3
00
0
0
0
2
0
2
Ref.1
Ref.2
Ref.3
Ref.4
Ref.5
Ref.6
Ref.7
: not activated, 1 low, 2 high.
: the display having only 2 numbers, the range will be indicated as 20 and 80 instead of 120 and
180.
: by setting “00”, the system is activated every time ignition is turned on; to deactivate, press the
push-button with the LED. Press again, to reengage the sensors.
: if your vehicle has an automatic transmission, select “ 1”.
: 0 not activated, 1 shows ldistance from the closest front obstacle, 2 shows distance from the
closest rear obstacle (insert reverse gear), 3 shows vehicle speed (in km/h, for programming
refer to parameter 11).
: 0
.
: 1 low, 2 standard, 3 high.
only if the car or obstacle is moving, 1 even if the vehicle or obstacle is not moving
Rif.1
Rif.2
: i
: 1 low, 2 standard, 3 high.
ncrease the value (setting can be modified from 0= deactivated, to 3) until the system no longer
detects the external spare wheel or the tow hitch
8.0 - PROGRAMMING
The unit display (front and rear) will show one of the following indications:
FS: Factory Setting, standard adjustment , “Factory parameters”.
CS: Custom Setting, user-chosen adjustment, “Custom Parameters”.
Only expert users should modify these settings to avoid malfunctions of the parking
system.
!
To activate the programming procedure proceed as follows:
Press one of the two push-buttons on the control unit and keep it pressed for at least two seconds;
the system will activate and enter in the programming mode.
Press the right push-button to go to the next
parameter.
Press the right push-button to increase the
value of the parameter.
When the parameter you want to modify is displayed, press one of the push-buttons and keep it
pressed until the display starts to blink; at this point you can modify the parameter.
Press one of the two
on the control unit and keep it pressed for at least two seconds
to register the value.
The display will stop blinking and the selected parameter will be displayed.
push-buttons
If no button is pressed within10 seconds, the system will exit the programming mode.
Press the left push-button to go to the previous
parameter.
Press the left push-button to decrease the
value of the parameter.
Press the two push-buttons on the control unit and keep them pressed for more than
two seconds to reset all the factory settings (FS).
!
