manualshive.com logo in svg

Gemalto Cinterion ELS31T-J, Описание аппаратного интерфейса, Страница: 68 / 102

Поделиться
Скачать
Gemalto Cinterion ELS31T-J Скачать руководство пользователя страница 68

Cinterion

®

 LTE Terminals Hardware Interface Description

6.5 Compliance with FCC and IC Rules and Regulations

70

ELSxT_HID_v04

2018-09-04

Confidential / Preliminary

Page 68 of 102

6.5

Compliance with FCC and IC Rules and Regulations

As an integrated product, the LTE Terminals are fully compliant with the grant of the FCC 
Equipment Authorization and the Industry Canada Certificates issued for the built-in LTE mod-
ules, and therefore, bear the labels “Contains FCC ID: QIPELS61-US” or “Contains FCC ID: 
QIPELS61-AUS“ or “Contains FCC ID: QIPELS31-V“.

The Equipment Authorization Certification for the Cinterion

®

 LTE modules is listed under the 

following identifiers:

FCC Idenitifier: QIPELS61-US or QIPELS61-AUS or QIPELS31-V
Industry Canada Certification Number: 7830A-ELS61US or 7830A-ELS31V
Granted to Gemalto M2M GmbH

Notes (FCC):

 

Radiofrequency radiation exposure Information:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled envi-
ronment. This equipment should be installed and operated with minimum distance of 20 cm be-
tween the radiator and your body. This transmitter must not be co-located or operating in 
conjunction with any other antenna or transmitter.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation.

This terminal equipment has been tested and found to comply with the limits for a Class B dig-
ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio communications. Howev-
er, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which can be de-
termined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications made to this equipment not expressly approved by Gemalto M2M 
may void the FCC authorization to operate this equipment. 

This device contains LTE, UMTS, GSM and GPRS class functions in the 700 (Bd28), 800/850 
(Bd6, Bd18, Bd19), 900, 1800 and 2100MHz bands that are not operational in U.S. Territories. 
This device is to be used only for mobile and fixed applications.

Users and installers must be provided with antenna installation instructions and transmitter op-
erating conditions for satisfying RF exposure compliance: For more information on the RF an-
tenna interface please refer to 

Section 3.15

 and 

Section 4.5

.

Содержание Cinterion ELS31T-J







































































































Отзывы:

Нет отзывов