manualshive.com logo in svg

Gemalto Cinterion ELS31T-J, Описание аппаратного интерфейса, Страница: 47 / 102

Поделиться
Скачать
Gemalto Cinterion ELS31T-J Скачать руководство пользователя страница 47

Cinterion

®

 LTE Terminals Hardware Interface Description

3.15 RF Antenna Interface

47

ELSxT_HID_v04

2018-09-04

Confidential / Preliminary

Page 47 of 102

3.15

RF Antenna Interface

The external RF antennas are connected via the LTE Terminals’s female SMA connectors that 
is also the antenna reference point (ARP).

Figure 21:  

Antenna connectors

The system impedance is 50

Ω

. In any case, for good RF performance, the return loss of the 

customer application’s antenna should be better than 10dB (VSWR < 2). LTE Terminals with-
stand a total mismatch at this connector when transmitting with maximum RF power.

Additional ESD protection to the antenna connector is provided. No DC voltage must be applied 
to the antenna circuit to protect it from damage.

Please note that the terminal should be installed and operated with a minimum distance of 
20cm between the antenna connected to the terminal and any human bodies. Also, the trans-
mitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The allowed maximum antenna gain (including cable loss) for stand-alone situation is given be-
low in 

Table 18

.

Table 18:  

Allowed maximum antenna gain (including cable loss)

Terminal

700
MHz

800
MHz

850
MHz

900
MHz

1700
MHz

1800
MHz

1900
MHz

2100
MHz

ELS61T-E

2.15dBi

2.15dBi

-

2.15dBi

-

2.15dBi -

2.15dBi

ELS61T-E2

2.15dBi

2.15dBi

-

2.15dBi

-

2.15dBi -

2.15dBi

ELS61T-AUS

2.15dBi

-

2.15dBi

2.15dBi

-

2.15dBi -

2.15dBi

ELS61T-US

2.15dBi

-

2.15dBi

-

2.15dBi -

2.15dBi -

ELS31T-J

-

t.b.d.

-

-

-

-

-

t.b.d.

ELS31T-V

7.4dBi

-

-

-

6.5dBi

-

-

-

Содержание Cinterion ELS31T-J







































































































Отзывы:

Нет отзывов