Gemalto Cinterion ELS31T-J Скачать руководство пользователя страница 21

Страница: 21 / 102

Cinterion

LTE Terminals Hardware Interface Description

2.1 Key Features at a Glance



ELSxT_HID_v04

2018-09-04

Confidential / Preliminary

Page 21 of 102

Output power (according

to Release 99, V5)

depending on frequency

band supported by mod-

ule

Class 4 (+33dBm ±2dB) for EGSM900

Class 1 (+30dBm ±2dB) for GSM1800

Class E2 (+27dBm ± 3dB) for GSM 900 8-PSK

Class E2 (+26dBm +3 /-4dB) for GSM 1800 8-PSK

Class 3 (+24dBm +1/-3dB) for UMTS 2100, WCDMA FDD BdI

Class 3 (+24dBm +1/-3dB) for UMTS 1900,WCDMA FDD BdII

Class 3 (+24dBm +1/-3dB) for UMTS 850, WCDMA FDD BdV

Class 3 (+24dBm +1/-3dB) for UMTS 800, WCDMA FDD BdVI

Class 3 (+24dBm +1/-3dB) for UMTS 900, WCDMA FDD BdVIII

Class 3 (+23dBm ±2dB) for LTE 2100, LTE FDD Bd1

Class 3 (+23dBm ±2dB) for LTE 1900, LTE FDD Bd2

Class 3 (+23dBm ±2dB) for LTE 1800, LTE FDD Bd3

Class 3 (+23dBm ±2dB) for LTE AWS, LTE FDD Bd4

Class 3 (+23dBm ±2dB) for LTE 850, LTE FDD Bd5

Class 3 (+23dBm ±2dB) for LTE 900, LTE FDD Bd8

Class 3 (+23dBm ±2dB) for LTE 700, LTE FDD Bd12

Class 3 (+23dBm ±2dB) for LTE 700, LTE FDD Bd13

Class 3 (+23dBm ±2dB) for LTE 800, LTE FDD B18

Class 3 (+23dBm ±2dB) for LTE 850, LTE FDD B19

Class 3 (+23dBm +1dB/-2dB) for LTE 800, LTE FDD Bd20

Class 3 (+23dBm ±2dB) for LTE 700, LTE FDD Bd28

The values stated above are maximum limits. According to Release 99, the

maximum output power in a multislot configuration may be lower. The nom-

inal reduction of maximum output power varies with the number of uplink

timeslots used and amounts to 3.0dB for 2Tx.

Power supply

Single supply voltage 8V to 57V

(Power-over-Ethernet support)

Operating temperature

(LTE module board

temperature)

Normal operation: -30°C to +85°C

Extended operation: -40°C to -30°C and +85°C to +90°C

Physical

Dimensions: 113.5mm x 75mm x 25.5mm

(excluding antenna and serial interface connectors)

Weight: 120g (approx.)

RoHS, WEEE

All hardware components are fully compliant with the EU RoHS and WEEE

Directives

LTE features

3GPP Release 9

UE CAT 1 supported

DL 10.2Mbps, UL 5.2Mbps

HSPA features

3GPP Release 8

(ELS61T-X only)

DL 7.2Mbps, UL 5.7Mbps

HSDPA Cat.8 / HSUPA Cat.6 data rates

Compressed mode (CM) supported according to 3GPP TS25.212

UMTS features

3GPP Release 4

(ELS61T-X only)

PS data rate – 384 kbps DL / 384 kbps UL

CS data rate – 64 kbps DL / 64 kbps UL

Feature

Implementation

Содержание Cinterion ELS31T-J







































































































Результаты поиска

Содержание Cinterion ELS31T-J

Отзывы:

Gemalto Cinterion ELS31T-J, Описание аппаратного интерфейса, Страница: 21 / 102

Результаты поиска

Содержание Cinterion ELS31T-J

Отзывы: