Gemalto Cinterion ELS31T-J Скачать руководство пользователя страница 4

Страница: 4 / 102

Cinterion

LTE Terminals Hardware Interface Description

Contents

122



ELSxT_HID_v04

2018-09-04

Confidential / Preliminary

Page 4 of 102

Electrical and Environmental Characteristics........................................................ 48

4.1

Absolute Maximum Ratings ............................................................................. 48

4.2

Electrical Specifications of the Application Interface........................................ 49
4.2.1

On/Off Control..................................................................................... 49

4.2.2

RS-232 Interface................................................................................. 49

4.2.3

USB Interface...................................................................................... 49

4.2.4

GPIO Interface .................................................................................... 50

4.2.5

Ethernet Interface ............................................................................... 51

4.3

Maximum Power Supply Ratings ..................................................................... 52

4.4

Operating Temperatures.................................................................................. 56

4.5

Antenna Interface............................................................................................. 57

4.6

Storage Conditions .......................................................................................... 60

Mechanics, Mounting and Packaging ..................................................................... 61

5.1

Mechanical Dimensions ................................................................................... 61

5.2

Mounting the LTE Terminals............................................................................ 64

5.3

Packaging ........................................................................................................ 65

Full Type Approval.................................................................................................... 66

6.1

Gemalto M2M Reference Setup ...................................................................... 66

6.2

Restrictions ...................................................................................................... 67

6.3

CE Conformity.................................................................................................. 67

6.4

EMC ................................................................................................................. 67

6.5

Compliance with FCC and IC Rules and Regulations ..................................... 68

6.6

Compliance with Japanese Rules and Regulations......................................... 70

List of Parts and Accessories.................................................................................. 71

Appendix A: (Hardware) Watchdog......................................................................... 73

8.1

Reset Conditions.............................................................................................. 74
8.1.1

Reset stages ....................................................................................... 74

8.1.2

Reset Delay ........................................................................................ 75

8.2

Restart Conditions ........................................................................................... 75

8.3

Complete Watchdog Configuration .................................................................. 76
8.3.1

Watchdog (WD) Command Specification ........................................... 76

8.4

Qualified Watchdog Configuration ................................................................... 86
8.4.1

C Interface Command Specification ................................................. 86

8.5

Configuring GPIO Directions............................................................................ 92
8.5.1

Configuration using I

C Interface ........................................................ 93

8.5.2

Configuration using TXD0 Line of ASC0 Interface.............................. 94

Содержание Cinterion ELS31T-J







































































































Результаты поиска

Содержание Cinterion ELS31T-J

Отзывы:

Gemalto Cinterion ELS31T-J, Описание аппаратного интерфейса, Страница: 4 / 102

Результаты поиска

Содержание Cinterion ELS31T-J

Отзывы: