background image

Cinterion

®

 Java Terminals Hardware Interface Overview

 Contents

124

EHSxT_BGS5T_HIO_v03

2016-05-26

Confidential / Released

Page 3 of 50

Contents

0

Document History ......................................................................................................  7

1

Introduction ................................................................................................................. 8

1.1

Related Documents ........................................................................................... 9

1.2

Terms and Abbreviations ................................................................................... 9

1.3

Regulatory and Type Approval Information ..................................................... 11
1.3.1

Directives and Standards .................................................................... 11

1.3.2

Safety Precautions.............................................................................. 14

1.4

Product Label ................................................................................................... 16

2

Product Concept ....................................................................................................... 17

2.1

Key Features at a Glance ................................................................................ 17

3

Interface Description ................................................................................................ 20

3.1

Overview .......................................................................................................... 20

3.2

Block Diagram.................................................................................................. 21

3.3

Operating Modes ............................................................................................. 22

3.4

RS-232 Interface .............................................................................................. 23
3.4.1

9-Pole D-sub Connector ..................................................................... 23

3.5

USB Interface................................................................................................... 24

3.6

GPIO Interface ................................................................................................. 24
3.6.1

Serial Interface ASC1 ......................................................................... 27

3.6.2

Digital Audio Interface......................................................................... 28

3.6.3

I

2

C Interface ........................................................................................ 29

3.6.4

SPI Interface ....................................................................................... 30

3.6.5

PWM Interface .................................................................................... 31

3.6.6

Pulse Counter ..................................................................................... 31

3.6.7

Analog-to-Digital Converter (ADC)...................................................... 31

3.6.8

DSR0 signal ........................................................................................ 31

3.7

Ethernet Interface ............................................................................................ 32

3.8

Power Supply ................................................................................................... 33

3.9

Power Up/Power Down Scenarios ................................................................... 34
3.9.1

Turn Java Terminals on ...................................................................... 34

3.9.2

Reset/Restart Java Terminals............................................................. 34

3.9.3

Turn Java Terminals off ...................................................................... 35

3.9.4

Disconnecting power supply ............................................................... 35

3.10

Automatic thermal shutdown............................................................................ 36

3.11

Hardware Watchdog ........................................................................................ 36

3.12

RTC.................................................................................................................. 36

3.13

SIM Interface.................................................................................................... 37

3.14

Status LEDs ..................................................................................................... 38

3.15

RF Antenna Interface ....................................................................................... 39

Содержание Cinterion BGS5T USB



















































Отзывы: