Gema OptiGun GA03-E Скачать руководство пользователя | Manualshive

Страница: 25 / 45

background image

V 02/22

OptiGun GA03-E

Cleaning and maintenance

•

23

Cleaning and maintenance

General information

ATTENTION

All unauthorized modifications to the powder gun are forbidden for
safety reasons, and exempt the manufacturer from any liability
from resulting damage!

Regular, careful cleaning and maintenance extends the service
life of the gun and ensures long-lasting, uniform coating quality!

– The parts to be replaced during maintenance work are available

as spare parts. These parts can be found in the corresponding
spare parts list!

Cleaning

Gun cleaning

ATTENTION

The following solvents may not be used to clean the gun:

► Ethylene chloride, acetone, ethyl acetate, methyl ethyl ketone,

methylene chloride, premium gasoline, turpentine, tetrachloro-
methane, toluene, trichloroethylene, xylene!

1.

Only cleaning agents with a flash point of a least 5 Kelvin above
the ambient temperature, or cleaning places with technical venti-
lation are allowed!

Before cleaning the powder gun, switch off the control unit. The
compressed air used for cleaning must be free of oil and water!

Daily

1.

Blow off the outside of the gun and wipe, clean etc.

Weekly

2.

Remove powder hose

«
...
23
24
25
26
27
...
»

Содержание OptiGun GA03-E














































Отзывы:

Нет отзывов

Похожие инструкции для OptiGun GA03-E

Бренд: Eaton Страницы: 12

Бренд: Fein Страницы: 53

MagicLift 25057

Бренд: Omega Lift Страницы: 24

Бренд: Parkside Страницы: 45

Бренд: Parkside Страницы: 76

Бренд: Parkside Страницы: 46

Бренд: Parkside Страницы: 99

Бренд: Parkside Страницы: 40

Бренд: Bison Страницы: 44

Бренд: Hilti Страницы: 138

Бренд: Parkside Страницы: 28

Бренд: H&H Страницы: 20

Бренд: PASCO Страницы: 36

Carlyle Tools 6-711A

Бренд: Napa Страницы: 16

Бренд: TSPROF Страницы: 17

Бренд: Tyco Electronics Страницы: 8

Бренд: Auplex Страницы: 3

Бренд: MGC Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды