Gema MultiStar CG10 Скачать руководство пользователя страница 53

Страница: 53 / 64

Rev. 00 08/17

MultiStar CG10

Fault clearance



Code

Description

Criteria

Remedy

H27

EEPROM verification
erroneous

EEPROM error

Contact a Gema service
center

CAN bus:

H40

Permanent CAN bus
error

The CAN controller changes into
BUS OFF condition.
No power supply or cable is not
connected.

Connect the cable,
otherwise contact Gema
service

H41

High error rate when
transmitting/receiving

The CAN controller changes into
ERROR_PASSIVE condition

Contact a Gema service
center

H42

Overflow on data
reception

The message to be received has
no more place in the receiver
buffer. Messages are sent faster
than they can be processed.

Contact a Gema service
center

H43

Overflow on
transmission

The message to be sent has no
more place in the transmission
buffer. Messages are produced
faster than they can be sent.

Contact a Gema service
center

H44

Master failed

Node Guarding message is
missing longer than 2 seconds.
Connection to master failed.

Check the connection to the
Master, otherwise contact
Gema service

H45

Parameter value
outside the value
range

The sent parameter value is
outside the allowed value range

Check input values

H46

Invalid Node ID set

The Node ID is not between 1
and 127

Set Node ID to 127

H47

No CAN interface
installed

CAN interface is selected in the
system parameters, but no
interface is installed

Contact a Gema service
center

H48

No ACK to "Boot Up
Message" received

No CAN node is answering to the
"Boot Up Message".

Check cabling connections
between the users,
otherwise contact Gema
service

Throttle motors:

H60

Conveying air
reference position not
found

Throttle motor or needle jammed,
limit switch defective, error in
motor throttle

Contact a Gema service
center

H61

Supplementary air
reference position not
found

Throttle motor or needle jammed,
limit switch defective, error in
motor throttle

Contact a Gema service
center

H62

Electrode rinsing air
reference position not
found

Throttle motor or needle jammed,
limit switch defective, error in
motor throttle

Contact a Gema service
center

H63

Conveying air throttle
does not move

Short circuit in limit switch, motor
throttle defective

Contact a Gema service
center

H64

Supplementary air
throttle does not move

Short circuit in limit switch, motor
throttle defective

Contact a Gema service
center

H65

Electrode rinsing air
throttle does not move

Short circuit in limit switch, motor
throttle defective

Contact a Gema service
center

H66

Conveying air position
lost

Lost steps, limit switch defective,
throttle motor defective

Contact a Gema service
center

Содержание MultiStar CG10

































































Результаты поиска

Содержание MultiStar CG10

Отзывы:

Бренды по названию

Популярные бренды

Gema MultiStar CG10, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание MultiStar CG10

Отзывы:

Бренды по названию

Популярные бренды