2-2
www.geith.com
SAFETY
Proper Work Tools and Attachments
When installing and using optional attachments, read the
instruction manual for attachment, and general
information related to the attachments in this manual.
Attachments and attachment control systems that are
compatible with the machine are required for safe and
reliable machine operation. Do not exceed maximum
operating weight (machine weight plus attachment) that
is listed on the machine’s certification plate and reference
lift capacity per the load chart in the machine.
Make sure that all guards and shields are in place on
machine and on work tool. Depending on type or
combination of work equipment, there is a potential that
work equipment could interfere with the cabin or other
parts of machine. Before using unfamiliar work
equipment, check if there is any potential of interference,
and operate with caution.
While you are performing any maintenance, testing, or
adjustments to attachments, stay clear of the following
areas: cutting edges, pinch points, and crushing
surfaces.
Never use attachment as a work platform or man-lift.
Pressurized Fluids
Pressurized air or fluids can cause debris and/or fluids to
be blown out. This could result in death or serious injury.
Immediately after operations are stopped, coolant,
engine oil, and hydraulic oil are at their highest
temperatures and the radiator and hydraulic tank are still
under pressure. Always wait for temperature to cool
down and follow specified procedures when performing
the following operations. Follow specified procedures
when attempting to remove caps, drain oil or coolant, or
replacing filters. Failure to do so can result in death or
serious injury.
When pressurized air and/or pressurized water is used
for cleaning, wear protective clothing, protective shoes,
and eye protection. Eye protection includes goggles or a
protective face shield.
Pressure can be trapped in a hydraulic system and
should be relieved before maintenance is started.
Releasing trapped pressure can cause sudden machine
movement or attachment movement. Use caution if you
disconnect hydraulic lines or fittings.
High-pressure oil that is released can cause a hose to
whip or oil to spray. Fluid penetration can result in death
or serious injury. If fluid enters skin or eyes, get
immediate medical attention from a physician familiar
with this injury.
Personal Protective Equipment (PPE)
Do not wear loose clothing and accessories. Secure long
hair. These items can snag on controls or on other parts
of equipment.
Do not wear oily clothes. They are highly flammable.
Do not forget that some risks to your health may not be
immediately apparent. Exhaust gases and noise pollution
may not be visible, but these hazards can cause
disabling or permanent injuries. Breathing masks and/or
ear protection may be required.
Wear a hard hat, safety shoes, safety goggles, mask,
leather gloves, earplugs and other protective equipment,
as required.
Proper Tools and Clothing
Only use tools that are intended for the type of service to
be done and never use inadequate tools. Metal pieces
from low quality or damaged tools, such as chisels or
hammers, can break off and hit a service person in the
eyes or face causing serious injury.
Hydraulic System
Check hydraulic tubes, hoses and fittings for damage,
wear or for leaks. Hydraulic lines and hoses must be
properly routed and have adequate support and secure
clamps. Leaks can cause fires. Never use a flame or
bare skin to check for leaks.
Tighten or replace any parts that show leakage.
Check that all hose and tube clamps, guards, and
cushions are securely attached. If they are loose, they
can vibrate during operation and rub against other parts.
This can cause damage to hoses and cause
high-pressure oil to spray on hot surfaces, causing a fire
and death or serious injury.
Always clean fluid spills. Do not use gasoline or diesel
fuel for cleaning parts. Use commercial nonflammable
solvents.
Содержание QC100 H1
