Gehl RS5-19 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 82

background image

PRINTED IN U.S.A.

17

50960066/AP0813

GUARDS AND SHIELDS

Whenever possible and without affecting machine
operation, guards and shields are used to protect poten-
tially hazardous areas. In many places, decals are also
provided to warn of potential hazards and to display
special operating procedures.

WARNING

Read and thoroughly understand all safety
decals on the Telescopic Handler before oper-
ating it. DO NOT operate the machine unless
all factory-installed guards and shields are
properly secured in place.

CAUTION

Before operating the Telescopic Handler,
become familiar with and know how to use
ALL safety devices and controls. Know how to
stop the machine operation before operating
it. This Gehl machine is designed and intend-
ed to be used ONLY with a Gehl Company
attachment tool, or a Gehl Company approved
accessory or referral attachment tool. Gehl
Company cannot be responsible for safety if
the machine is used with an unapproved
accessory or attachment tool.

Chapter 5

INDICATORS AND CONTROLS

Operator’s Compartment and Indicators/Controls Locations

Frame Angle

Indicator

Boom Control

Joystick

Key Switch

Start Button

Boom Angle

Indicator

Brake Pedal

Attachment / Auxiliary

Hydraulics Joystick

Arm Rest

Throttle Pedal

Steering Wheel

Instrument and

Switch Panel

Horn Button

Travel Direction

Lever

«
...
17
18
19
20
21
...
»

Содержание RS5-19



















































































Отзывы:

Нет отзывов

Похожие инструкции для RS5-19

Бренд: Badger Meter Страницы: 48

Бренд: Miller Страницы: 16

PYTHON-PLUS K2447-1

Бренд: Lincoln Electric Страницы: 39

WK MIG 5040 F SYNERGIC

Бренд: WELDKAR Страницы: 84

Бренд: WARPP Страницы: 10

Бренд: Firepower Страницы: 52

20/20 SeedSense

Бренд: Precision Planting Страницы: 65

Devicenet R7F4DD-DC16B-H

Бренд: M-system Страницы: 7

Бренд: PVI Страницы: 12

Бренд: Hitachi Страницы: 242

Бренд: morse Страницы: 6

Бренд: Daintree Страницы: 7

Бренд: Lincoln Electric Страницы: 38

Power Mig 215 XT

Бренд: Lincoln Electric Страницы: 8

Бренд: Lincoln Electric Страницы: 46

Power Wave AC/DC 1000

Бренд: Lincoln Electric Страницы: 74

POWER MIG SVM157-A

Бренд: Lincoln Electric Страницы: 91

LECS-080-4400-00

Бренд: Lincoln Electric Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды