st.32
xead
pa.01
pa.14
• U.CAL
• Lin
Lin
Custom linearization for main
or aux input (*)
Step 0
Step 32
......
Scale limits
Scale limits
• CuSt
Set number of parameters
in custom menu
[ 0 ... 14 ]
CuSt
Set custom “dAtA” menu
Identification code for
parameter 1
Identification code for
parameter 14
......
X X X X
x
The identification code is specified in this
position, under the parameter name
U.CAL
User calibration
U.CAL Function
1 Analogue output 1
2 Analogue output 2
3 Input 1 - custom probe 10V
4 Input 1 - custom probe 50mV
5 Input 2 - potentiometer
(*) Not available for:
16-step programmer (SPPt = 3)
programmer with control parameter groups (SPPt = 2)
input correction function enabled (SEnS + 8)
custom TC input (SEnS = 0; tyPE = 20, 21)
custom RTD input (SEnS = 1; tyPE = 4, 5)
custom PTC input (SEnS = 2 ; tyPE = 2, 3)
Start/Stop
Programmer
(0...63)
0
from enabled digital input
1
from AL1 ON
2
from AL2 ON
3
from AL3 ON
4
5
from serial line (address 0049H, bit 0)
6
from serial line (address 0049H, bit 1)
7
from keys
Reset
Programmer
(0...15)
st.00
bvtt
al.nr
sns.2
sens
+ 8 to enable HB alarm
+ 16 to enable LBA alarm
SnS.2 Signal
0
0 ... 1V
1
0.2 ... 1V
2
0 ... 10V
3
2 ... 10V
4
0 ... 20mA
5
4 ... 20mA
6
Potentiometer
7
CT 50mA
~
AL.nr Alarm 1
Alarm 2
Alarm 3
0
disabled
disabled
disabled
1
enabled
disabled
disabled
2
disabled
enabled
disabled
3
enabled
enabled
disabled
4
disabled
disabled
enabled
5
enabled
disabled
enabled
6
disabled
enabled
enabled
7
enabled
enabled
enabled
Function
0 none (key disabled)
1
MAN / AUTO select
2
LOC / REM
3 HOLD
4
Start / Stop self-tuning
5
Start / Stop autotuning
6
Set / Reset outputs OUT 1 ... OUT 4
7 Reset alarms memory
8 -
9 Instantaneous integral reset
10 START / STOP Programmer (if enabled in S.S.t.)
11 RESET Programmer (if enabled in _ _ r.t.)
Selection
of probe type
for aux input
Select number of
enabled alarms
Function of M/A keys: “
≠
”
Note: scale selection with “tYPE” code in InP.
SEnS Probe type for main input
0
Thermocouple (TC)
1
Resistance Thermometer (RTD)
2
Thermistor (PTC)
3
Voltage 0...50mV / 10...50mV
4
Current 0...20mA / 4...20mA
5
Voltage 0...10V / 2...10V
6
Custom 10V
7
Custom max 50mV
Selection of
probe type for
main input
+16 disable function in configuration menu
(only for butt parameters)
+8 to enable main input curve 4 point correction (alternative to custom linearization).
See description in “Main Input Correction Function” section.
+16 to disable averaging filter on sampled value (available from software release 3.05)
+8 to disable averaging filter on sampled value (available from
software release 3.05)
bvt.2
led.3
led.2
led.1
d.i.F.1, d.i.F.2
Function of
digital input 1
(IN1)
+ 16 for inverse logic input
+ 32 to force logic state 0 (OFF)
+ 48 to force logic state 1 (ON)
Function of
digital input 2
(IN2)
Defining SV
display function
LEd.x Function
0
none
1
MAN/AUTO (ON in manual, OFF in auto)
2
LOC/REM (ON in remote, OFF in local)
3
self-tuning enabled
4
autotuning enabled
5
IN1 repetition
6
IN2 repetition
7
enable serial dialogue
8
HOLD on
9
Error present (error code <> 0)
10
Softstart running
11
Program 0, 1, 2, 3 (LS bit)
12
Program 0, 1, 2, 3 (MS bit)
13
Programmer in START
14
Programmer in RESET
15
Programmer RUNNING
Function of “MAN” LEDs: M/A, L/R, ATUN, IN1, IN2 repetition,
event programmer, serial port enabled, errors present
+ 16 for flashing LED function
d.i.F.x Digital input function
0
none (key disabled)
1
MAN / AUTO select
2
LOC / REM
3
HOLD
4
Start / Stop programmer
5
Reset programmer
6
Software power on/off
7
Reset alarms memory
8
Select program 0, 1, 2, 3 (LS bit)
9
Select program 0, 1, 2, 3 (MS bit)
10
Advance program to end of cycle
11
Advance program to last step
12 Enable program advance
diSP Lower display (SV) function
0
SSP - setpoint enabled
1
InP.2 - aux input
2
Control output value
3
Deviation (SSP - PV)
LEd.1 (MAN), LEd.2 (AUX), LEd.3 (PRG)
bArG
bArG
0 Heat
1 Cool
2 Heat + Cool
3 PV
4 Aux input (position V2 valve)
5 Current setpoint
6 -
7 -
8 Deviation (PV-setpoint)
10%… + 10% of full scale
Bargraph
function
s.s.t.
-
r.t.
-
-
d.1.f.2.
d.1.f.1.
disp
+8 inverse action
+16 Autoreset enabled (Stop = program reset) (only for _S.S.t. parameter)
+16 reset from the set it puts into effect them without zero setting power (only for _ _ rt parameter)
+32 start from current value of process variable (only for _S.S.t. parameter)
9
80090G_MHW_1600-1800P_04-2013_ENG
